Geek Vape Aegis L200 Classic Kit

The Aegis L200 Classic mod comes back with a Z Max Tank clearomizer of the brand GeekVape, all for an airy vape in DL!

This performing electronic cigarette offers a power that can reach 200W, while having a simple functioning, making it more accessible to vape beginners. Its ON/OFF switch and its IP68 certification enable safe transport.

The Z Max Tank has an XL 6ml capacity and works with M Series coils. Whether it is thanks to its 810 drip tip or values of coils included (X and x ohm), this clearomizer is meant for an airy draw in direct inhaling.

GeekVape's Aegis L200 Classic kit

The design of Aegis L200 Classic kit

With 146 x 60 x 32mm dimensions and a 284g weight, this kit is meant for vapers looking for big equipment with great manufacturing quality. Thanks to its IP68 certification, it can be transported everywhere safely.

Its front side is only composed of a large and ergonomic Fire button, a 1.08" color screen, and setting buttons. On the top part, hidden under a silicon trapdoor, you'll find a USB-C port so you have a spare charge solution.

On the left side, a clever sliding button enables you to lock the whole mod so you don't change settings through inattention.

Below, you'll find a trapdoor to the dual 21700 or 18650 battery compartment.

Handling of Geekvape's Aegis L200 Classic kit

How does the kit work?

After 5 consecutive pushes on the Fire button, the mod turns on. You can select the functioning mode that suits you according to your preferences and your level:

• POWER: manually set the output power of the mod according to the coil installed
• BOOSTING: this mode automatically selects the power output
• TC/TCR: set the temperature according to the type of equipment used in your atomizer (Ni, Ti, SS)
• VPC (Curve): set the heating curves for a customizable vape in variable wattage

The use of these two last modes only works if you decide to install an atomizer on the mod.

The 1.08" color screen of Geekvape's Aegis L200 Classic kit

To avoid any involuntary pushes on the Fire button, the manufacturer thought of a clever locking button on the side of the mod.

The locking button of Geekvape's Aegis L200 Classic kit

A supply thanks to two 21700 or 18650 batteries

In order to reach 200W of power, but also for a big capacity, the Aegis L200 Classic mod has a compartment capable of holding two 18650 or 21700 batteries (not included) with the adaptors included.

To access the compartment, you only have to slide the button on the lower part of the mod.

The dual battery compartment of Geekvape's Aegis L200 Classic kit

For the most forgetful vapers, you'll find a USB-C port located under a silicon trapdoor directly on top of the mod.

Please note that recharging the batteries directly on an external charger is recommended.

The USB-C port of Geekvape's Aegis L200 Classic kit

The Z Max clearomizer

To accompany your mod, the manufacturer Geekvape matches it with a Z Max tank and its 810 drip tip for an airy vape in direct inhaling (DL).

Its pre-installed bulb Pyrex holds up to 6ml of e-liquid. In the box, you'll find a spare Pyrex offering 4ml of stock. With a top-filling system, this step is easily and quickly made.

This clearomizer works with M Series coils, two are included (0.4 and 0.2ohm).

Geekvape's Z Max clearomizer

The M Series coils

To enable you to directly vape by receiving your kit, Geekvape delivers two M Series coils in the kit's box.

Then, you'll benefit from:

• A 0.14ohm coil, pre-installed in your clearomizer. Made in KTR Mesh, the latter is used between 60 and 80 watts
• A 0.2ohm coil, made in KA1 Mesh. To use on a power range between 70 and 85W.

To install or change your coil, follow the steps below:

1. Unscrew the bottom part of your clearomizer
2. Soak a new coil with some e-liquid drops
3. Take the used coil off thanks to the tool included
4. Insert the new one in the right compartment
5. Screw the bottom part back

Wait for some minutes so the new coil is primed.

The Z Max's top airflow

In order to customize your vape, you'll find an airflow with opposed oval holes. Its top part will avoid any risks of leakages. Its sliding ring enables you to precisely set the position desired.

As a reminder, the more the airflow is open, the more the airflow in your vape is important, and your vape is cloudy.

The airflow of Geekvape's Z Max clearomizer

How to fill the clearomizer?

To fill it with e-liquid, the brand Geekvape thought of a clever top-filling system.

Then, you can proceed to the tank filling, you only have to:

1. Unscrew the top part of the clearomizer (top cap)
2. Insert the thin bottle tip of e-liquid in one of the two lateral holes
3. Fill
4. Close the top cap

As a reminder, if you use a new coil, wait for some minutes so the latter is primed.

The filling of Geekvape's Z Max clearomizer

Box contents

• 1 Aegis L200 Classic mod
• 1 6ml Z Max clearomizer
• 1 4ml spare Pyrex
• 1 0.2ohm M Series coil
• 1 0.14ohm M Series coil (pre-installed)
• 1 USB-C cable
• 1 bag of spare washers
• 1 user guide

The Aegis L200 Classic kit is made by Geekvape. It is delivered without batteries.

Box contents of Geekvape's Aegis L200 Classic kit