Innokin GO Z Kit

Innokin presents its GO Z kit, a tubular electronic cigarette that is 100% automatic for easy use!

It has a built-in battery with a capacity of 1500mAh. It also has a simple power switch that allows you to vape and check the remaining battery level.

Finally, it has a robust and easy-to-use PCTG clearomizer with a capacity of 2ml!

A tubular format

Measuring only 129mm in height and 20mm in diameter, the tubular look of the GO Z makes it easy to carry around. Very lightweight, it offers optimal handling.

But above all, made from premium stainless steel and food-grade PCTG, the GO Z kit is extremely durable. It's simple, nothing can stop it!

Innokin’s GO Z kit

A practical kit

To summarize, it doesn't get any simpler than the GO Z Pen kit by Innokin!

Equipped with a simple switch, all you have to do is press it while inhaling through the mouthpiece of the clearomizer to start vaping. The power is automatic, the safety features are enhanced... In other words, you don't have to worry about a thing, except making the most of the flavors of your chosen e-liquid!

The power switch of Innokin’s GO Z kit

A long-lasting battery!

This e-cig has a built-in battery with a capacity of 1,500mAh. If you can vape for hours, the GO Z kit will be able to follow you!

The kit can be charged anywhere. Simply connect the micro-USB cable included in the kit to the port located on the tube’s back.

The micro-USB port of Innokin’s GO Z kit

When do you need to charge it? Here again, the GOz kit takes care of everything! Its power switch will also double as a visual indicator:

• A green LED will light up when your battery level is between 100 and 71%
• A red and green LED will flicker if your battery is between 20 and 70% of its capacity
• Below 20%, the red LED will tell you that it is time to charge your device!

The GO Z MTL clearomizer

Innokin had to find a suitable companion for its practical and ergonomic electronic tube. Therefore, the company has created the GO Z MTL clearomizer. 

Discover this small and charming device, made from a stainless steel frame and PCTG tank, with a capacity of 2ml, adjustable air intakes, proprietary drip tip, and Z-Coils!

The GO Z MTL clearomiser from Innokin’s GO Z kit

The Z-Coils

Highly suited to beginner vapers or avid fans of tight draws, very similar to the feel of a traditional cigarette, Zenith Coils or Z-Coil coils allow for indirect inhaling (MTL) vaping.

Already included with your GOz kit, you will find a 1.6ohm Z-Coil coil, the most effective in terms of flavors and throat hit. However, you will also be able to equip your clearomizer with other coils: from 0.6ohm to 1.6ohm.

To install your new coil, simply unscrew the clearomizer from the 510 connector on your built-in GO Z battery. Then unscrew the air intake ring on the clearomizer to reach the coil. Pull it out and push it in to insert it.

N.B.: Don't forget to soak the cotton of your coil with a few drops of e-liquid. When properly primed, your coil will last longer and you'll avoid many mishaps!

The airflow of Go

Because every vaper is different, the GO Z kit will allow you to fine-tune your draw, and therefore your throat feel.

To do so, you have to turn the airflow knob, located beneath the PCTG tank. By turning it, you will discover several airflow combinations, from a nearly closed airflow (for a tight draw) to a more open one (for a smoother feel).

The adjustable air intakes of Innokin’s GO Z kit

A 2ml PCTG tank that’s filled through the top

The clearomizer’s tank is made from PCTG, which is a particularly solid material. Its 2ml capacity will provide you with more than enough juice to last your vaping breaks!

The tank is filled from above. By sliding the top cap outwards, you’ll see a filling hole coated in silicone for a clean refill!

You have to wait a few minutes after filling the GO Z MTL clearomizer with e-liquid. Doing so will ensure the coil is properly primed and ready to vape!

The top-fill system of Innokin’s GO Z kit

Contents of the box

• A GO Z electronic tube with a built-in battery
• A GO Z MTL clearomizer
• A 1.6ohm Z-Coil
• A micro-USB cable
• A user guide

The GO Z kit is manufactured by Innokin.

Contents of the box of Innokin’s GO Z kit