Dotmod DotBox 100W Kit

Opt for an airy and tasty vape with the DotBox kit! Discover it in detail in this unboxing video!

The manufacturer Dotmod comes back with a kit, betting on simplicity and power but also compactness!

You'll find a DotBox going from 100W of power and with a leather effect. Functioning with a 21700 or 18650 battery, thanks to the adapter included, you'll enjoy a big capacity. With numerous modes, it adapts to vape experts and beginners.

It is matched with a 5ml DotTank Max clearomizer and is compatible with the Dotcoil coils. This tank is mainly meant for a vape in the direct draw (DL).

Dotmod's DotBox 100W kit

The design of DotBox 100W kit

Dotmod offers the DotBox, a mod equipped with a leather-effect coating marked with the brand name and an engraved gold-colored fire switch.

The mod measures 146 x 39 x 25mm and weighs 230g. It complies with the IP67 standard, which indicates resistance to water and dust.

The front panel features a round fire switch that is easy to press. Below that, you will find a pleasant color screen and two adjustment switches.

A unique feature of this mod is the full lock switch located on the top edge, next to the clearomizer!

Handling of Dotmod's DotBox 100W kit

A complete functioning

The manufacturer presents a mod that will adapt to the needs of vape beginners and experts. You'll find:

• Power mode: Manual power setting between 5 and 100 watts
• AUTO: Automatic power setting on 4 levels (very soft to strong)
• Boost mode: Increase the power delivered in the first second

For expert users of an atomizer or dripper, use the modes:

• Ni
• Ti
• SS
• Curve
• Bypass

The color screen of Dotmod's DotBox 100W kit

A 21700 or 18650 battery

To benefit from the 100W power of this mod, you can install it according to your preferences and your actual battery, a 21700 or 18650 battery, thanks to an adapter.

To take your battery out, you'll have to lift the metallic strip located below and then unscrew it to access the single battery compartment of this mod.

The single 21700/18650 battery compartment of Dotmod's DotBox 100W kit

If you need to charge but don't have an external charger, you can count on a USB-C port located under the silicon strip beside the battery compartment door, and a cable included.

The USB-C port of Dotmod's DotBox 100W kit

A 5ml tank

With a 5ml Pyrex bulb, a 510 drip tip but also compatibility with the DotCoil coils, this DotTank Max clearomizer will match your mod thanks to a 25mm diameter.

It is recommended for an airy vape in direct inhaling (DL). It is delivered with two coils with a value of 0.15 and 0.3ohm.

Please note, however, that with some clearomizers that are smaller in diameter than the DotTank Max, there may be a slight gap at the 510 pin, which can reduce the stability of the assembly. We therefore recommend using the DotTank clearomizer from Dotmod, which is included in this kit.

Dotmod's DotTank Max clearomizer

A multitude of coils compatible

By making its clearomizer with all DotCoil coils, the brand Dotmod offers a multitude of vape experiences according to the value of the coil installed.

Find inside the box two coils of different values. The first in 0.15ohm authorizes a vape between 60 and 800W in a direct draw. The second in 0.3ohm is more oriented for a vape in a restrictive direct draw (RDL) with a power range between 20 and 40W.

When you feel a light burnt taste or a loss of flavors, it is time to change the coils. For this, follow the guide below:

1. Unscrew the base of the clearomizer
2. Pull out the used coil
3. Soak your new coil with some drops of e-liquid
4. Put it in the same place
5. Carefully close the low part

An easy top airflow

The airflow of the clearomizer is located on the upper part. It can be adjusted by turning the upper ring to open or close the air intake holes.

The airflow ring of Dotmod's DotTank Max clearomizer

A 5ml capacity

To enjoy your favorite e-liquid, trust a big capacity of 5ml, thanks to the bulb pyrex installed.

To fill it with e-liquid, you only need to:

1. Unscrew the top part
2. Insert the thin tip of your e-liquid bottle into one of the two lateral holes
3. Fill
4. Close the top part
5. Vape!

In case you use a new coil, wait for some minutes to let it prime.

Filling of Dotmod's DotTank Max clearomizer

Box contents

• 1 DotTank 100W mod
• 1 DotTank Max clearomizer
• 1 0.15ohm DotCoil coil
• 1 0.3ohm DotCoil coil
• 1 USB-C cable
• 1 spare Pyrex
• 1 set of accessories

The DotBox 100W kit is made by Dotmod. It is sold without batteries.

Box contents of Dotmod's DotBox 100W kit