Voopoo Drag S3 Podmod

Are you looking for a tubular kit with great capacity?

Here is the S3 version of Voopoo's Drag podmod!

This electronic cigarette has a 3,000mAh built-in battery, rechargeable via USB-C.

It has a PnP X MTL cartridge, compatible with the PnP X coils of the manufacturer (from 0.3ohm).

Also note that the Drag S3 podmod presents a capacitive Switch button; in other words, it is only activated at the touch of your finger.

Voopoo's Drag S3 podmod

A compact podmod

Like all kits of the Drag series, the S3 presents a tubular format.

With dimensions of 124.2x33x28mm for a weight of 150g, the Drag S3 podmod is both compact and ergonomic.

From top to bottom, find on the main side:

• A switch button
• A 0.96" TFT color screen
• Two setting buttons
• A USB-C port

Handling Voopoo's Drag S3 podmod

A simple and intuitive functioning

According to your needs, you'll select the functioning mode that suits you among:

• SMART mode: automatic power adjustment according to the type of coil installed
• RBA mode: manual setting of the power, from 5 to 80W
• ECO mode: automatic adjustment of the podmod's settings, limiting the battery consumption

These modes are made by the performing QUEST 2.0 chipset of your Drag S3, and are accessible via the screen and the two setting buttons.

The screen of Voopoo's Drag S3 podmod

A capacitive switch button

The particularity of this Drag S3 is in its ignition button.

Indeed, the latter has a smart system that enables it to be activated with the touch of a finger.

Your electronic cigarette is protected against involuntary activations, especially during its transport.

The Switch button of Voopoo's Drag S3 podmod

A 3,000mAh capacity

In terms of power, the Drag S3 has a 3,000mAh built-in battery.

It can be charged quickly and easily via its USB-C port, located just below the adjustment buttons.

To do this, use the USB-C cable provided in the box with the Voopoo device.

The USB-C port of Voopoo's Drag S3 podmod

The PnP X MTL cartridge

Magnetically connected to your Drag S3, the PnP X MTL cartridge is specially made to hold the PnP X coils of the manufacturer.

It has a 5ml tank and a 510 drip tip, particularly suited to a tight draw in indirect inhaling.

The PnP X MTL cartridge of Voopoo's Drag S3 podmod

Two PnP X coils included

Ready-made,  your Drag S3 is ready to go as soon as you receive it.

Indeed, Voopoo adds two compatible coils to this kit:

• 1 0.8ohm PnP X coil (pre-installed): to use between 12 and 16W for a tight draw in indirect inhaling (MTL)
• 1 0.6ohm PnP X coil: to use between 18 and 23W, for a vape a bit less restrictive in indirect inhaling (MTL) or in restrictive direct inhaling (RDL)

Does your coil start to show some signs of wear (loss of flavors, light burnt taste)?

It is time to replace it with a new one!

For this:

1. Take the cartridge off the base
2. Pull on the used coil to take it out of its compartment
3. Soak a new coil with some e-liquid drops
4. Insert this new coil in its compartment of the old one
5. Fill the e-liquid tank
6. Reconnect the cartridge of the podmod
7. Wait for 5 to 10 minutes before vaping so the coil is correctly primed with e-liquid

Adjustable air intakes

In addition to the coil, you can also vary your vaping experience using the airflow ring.

Located at the top of the cartridge, this ring allows you to increase or decrease the airflow.

Simply turn the ring to quickly switch from a very tight draw to a slightly more airy vape.

The airflow of Voopoo's Drag S3 podmod

5ml fillable with e-liquid

To accompany your Drag S3, Voopoo bets on its PnP X MTL cartridge, with a 5ml e-liquid capacity.

This large-capacity tank is easy to fill using a silicone tab system.

When it's time to refill with e-liquid, follow the steps below:

1. Disconnect the cartridge from its magnetic base
2. Lift the strip
3. Insert the bottle tip of your bottle into the filling hole
4. Pour the e-liquid
5. Carefully close the silicone strip
6. Replace the cartridge on its magnetic base
7. Vape

As a reminder, if you are using a new coil, wait a few minutes before vaping to allow it to properly soak up the e-liquid.

Filling the PnP X MTL cartridge of Voopoo's Drag S3 podmod

Box contents

• 1 3,000mAh Drag S3 podmod
• 1 5ml PnP X MTL cartridge
• 1 0.6ohm PnP X coil
• 1 0.8ohm PnP X coil (pre-built)
• 1 spare 510 drip tip
• 1 USB-C cable
• 1 user guide

The Drag S3 podmod is made by Voopoo.

Box contents of Voopoo's Drag S3 podmod