Vaporesso Target 100 kit
A versatile 100W kit for airy vaping
-
Diameter24mm
-
Volume5ml
-
Battery type18650x1 or 21700x1
-
Brand
Make beautiful clouds wherever you go, thanks to Vaporesso’s compact and lightweight Target 100 kit!
Discover a modern electronic cigarette that can use a single 21700 or 18650 battery (not included), equipped with a quality Axon 2.0 chipset for a tailor-made vaping experience, whether you prefer simple or more complex vape modes.
A modern kit that’ll go everywhere with you!
Thanks to its sleek shape, the Target 100 kit is comfortable to handle. The mod is robust and has a pleasant woven cover on its rear. As for the clearomiser, its 25mm diameter and straight tube shape give the whole a very clean look.
With its 140.3mm height, 35.1mm width, and 28.6mm depth, the Target 100 kit will fit in the palm of your hand, and without weighing a ton either!
Vaporesso’s Target 100 kit
The powerful, safe, and versatile Axon 2.0 chipset
The Target 100 electronic cigarette is equipped with the same chipset as its predecessor, the Target 200. It offers a wide range of electronic protections and vaping modes and can reach a maximum power of 100W:
- The variable wattage mode (VW) lets you manually adjust the wattage
- The variable voltage mode (VV) lets you manually adjust the voltage
- The SMART mode caps the power depending on the coil you’re using
- The Pulse mode lets you increase the intensity of your puffs
- The F(t) mode allows you to gradually adjust the temperature that’s sent to your coil during your puffs
- The Bypass mode will delight the fans of mechanical mods!
Vaporesso’s device has a wide 0.96" TFT color screen and several adjustment buttons for browsing through all these settings.
The screen of Vaporesso’s Target 100 mod
A single 21700 or 18650 battery
One of the strong points of Vaporesso’s Target 100 kit? Its excellent endurance, due to its 21700 or 18650 single battery. To insert one of these batteries, you will open the flap beneath the mod.
Please note that for the 18650 battery you will need the adapter included in the kit.
The single battery (21700 or 18650) compartment of Vaporesso’s Target 100 mod
Need to charge your kit whilst out and about? No worries! Vaporesso has equipped its device with a USB-C port! Located on the front of the mod, it just needs to be connected to an external power source using the cable provided.
Please note that charging this way should remain occasional. It is always best to charge your battery(ies) using a dedicated external charger (sold separately).
The USB-C port of Vaporesso’s Target 100 mod
The 5ml iTank clearomiser
Like its predecessor, the 5ml iTank clearomiser has a diameter of 24mm. However, it holds a bit less e-liquid, 5ml instead of 8ml. Rest assured that this is more than enough for any cloud-chasing session!
The iTank’s style is both sleek and sober, going perfectly well with the Target 100 mod, making for a harmonious, simple and effective kit!
The 5ml iTank clearomiser of Vaporesso’s Target 100 kit
The GTi coils, built for both vapor and flavor
Vaporesso’s 5ml iTank clearomiser comes with two GTi Mesh coils:
- One 0.2ohm GTi coil, to be used between 60 and 70 watts for a good amount of vapor with a direct inhale (DTL)
- One 0.4ohm GTi coil, to be used between 50 and 60W for a more moderate vapor production with a restrictive direct inhale (RDL)
To set up your coil:
- Unscrew the clearomiser’s base
- Remove the old coil and replace it with a new one (previously soaked with a few drops of e-liquid)
- Screw the base back on and fill the tank
Always wait a good ten minutes before you start vaping with a new coil!
Versatile air intakes
There’s a triple airflow system that allows you to vape with either a direct inhale (DTL) or a more restrictive direct inhale (RDL). Simply rotate the airflow ring from right to left to find the ideal draw for your needs and suited to the coil you’ve installed.
The air intakes of the iTank clearomiser
5ml Pyrex tank and easy top fill
The iTank clearomiser has a 5ml straight tank, made from quality Pyrex material. There’s a spare tank in the kit as well, if ever something happens to the original one.
Filling the tank is extremely simple. Simply slide the top cap outwards with your finger to reveal the filling hole. Then, insert the tip of your bottle of e-liquid and fill up the tank with juice.
Remember to wait a few minutes after filling so that your coil is properly soaked with e-liquid.
The top-fill system of the iTank clearomiser
Contents
- The Target 100 mod
- The 5ml iTank clearomiser
- A spare 5ml Pyrex tank
- A pre-installed 18650 battery adapter
- One 0.2Ω GTi coil
- One 0.4Ω GTi coil
- A set of spare parts
- A USB-C cable
- A user guide
The Target 100 kit is manufactured by Vaporesso.
Contents of the box of Vaporesso’s Target 100 kit
Diameter | 24mm |
---|---|
Volume | 5ml |
Battery type | 18650x1 or 21700x1 |
Height | 140.3mm |
Width | 28.6mm |
Depth | 35.1mm |
Batteries included | No |
Mod type | Electronic |
USB charging | Yes |
Chipset | Axon Chip |
Chipset version | Vaporesso |
Compatible coils | GTi coils |
Tank | Pyrex |
Fill type | From above |
Drip-tip | Proprietary |
Connector pin | 510 |