Voopoo Vmate E2 Podmod

A small handy and simple podmod to use for beginners, discover the VMate E2 podmod in this video

A handy and simple-to-use podmod but in a format thought for more cleanliness? Discover Voopoo's VMate E2 podmod!

This electronic cigarette has a 1,500mAh built-in battery and 100% automatic functioning. It takes care of all the settings, so all you have to do is inhale through the mouthpiece to vape! Once you've finished puffing, a hygienic cap keeps your material clean.

Regarding the disposable cartridges, the VMate Top Fill offers 3ml of capacity, an intuitive filling system, and already installed sealed coils! Once worn out, throw the whole cartridge out and take a new one!

Particularly suited if you start vaping, the VMate E2 podmod is meant for a tight draw in indirect inhaling (MTL) or a vape a bit airier in restrictive direct inhaling (RDL).

A screen is built into the podmod's bright bar, so you can check battery capacity in real time!

Voopoo's VMate E2 podmod

A leather-effect coating

Handy, compact, and light, the VMate E2 podmod presents 95x33.5x19mm dimensions for a 92g weight.

Its structure in zinc alloy is covered with a leather-effect covering for a modern and chic design.

Handling of Voopoo's VMate E2 podmod

Voopoo adds a system with a magnetic cap allowing you to benefit from the best hygiene and clean condition for your mouthpiece.

The magnetic cap of Voopoo's VMate E2 podmod

A podmod with an intuitive use

When we say podmod, we mean a single-connector electronic cigarette that combines both a built-in battery and a dedicated cartridge. The VMate E2 podmod is made from a body with a built-in 1,500mAh battery and a disposable PCTG cartridge, which sits naturally on its magnetic base.

What sets the VMate E2 podmod apart from other devices of its kind is its particularly easy, intuitive operation. In fact, it's totally automatic!

The magnetic connection between Voopoo's cartridge and VMate E2 podmod

An entirely automatic functioning

Did you just start vaping? Are you already a vaper and looking for intuitive and simple equipment?

Here is for you the VMate E2, a podmod with 100% automatic functioning: no button or setting, you only have to inhale into the mouthpiece to vape!

According to the value of the coil used, your podmod will set the power delivered from 5 to 30W.

Voopoo lets you choose to adjust the air intakes through an airflow button located below the cartridge.

Simply slide the button to switch from a tight draw to an airier vape.

The airflow button of Voopoo's VMate E2 podmod

A built-in battery rechargeable by USB-C

As it is a beginner podmod, it will be easy to use and recharge. The VMate E2 podmod chooses a 1,500mAh built-in battery for a great capacity and an easy recharging system in USB-C!

You'll find a USB-C port hidden on the bottom.

The USB-C port of Voopoo's VMate E2 podmod

To proceed with the recharging, a USB-C cable is included in your box. To inform you of the battery level, use the screen integrated on the bright bar, located on the podmod's side.

The screen display is triggered by the inhaling and indicated the percentage of capacity left.

The screen of Voopoo's VMate E2 podmod

The VMate Top Fill cartridge

The VMate E2 podmod is delivered with two VMate Top Fill cartridges, each with a 3ml tank and a sealed coil.

According to the type of draw wished, you'll use in your e-cig one of the two following cartridges:

• VMate Top Fill cartridge with a 0.7ohm coil (pre-installed): for a tight vape in indirect inhaling (MTL)
• VMate Top Fill cartridge with a 0.4ohm coil: for a semi-aerial draw in restrictive direct inhaling (RDL)

Note that your VMate E2 podmod is also compatible with Voopoo's VMate V2 cartridges.

After two to three weeks of use, the built-in coil will show some wear signs (loss of flavors, light burnt taste), it will be time to change the whole cartridge with a new one.

The cartridge of Voopoo's VMate E2 podmod

An easy and clean filling

Voopoo also simplifies the vape by giving its VMate E2 podmod with a top filling system, no need to take the cartridge off the podmod when you fill it with e-liquid!

Follow the steps below to easily and quickly fill the 3ml of the tank:

1. Take the cap off the VMate E2
2. Repair the silicon strip on the side of the cartridge and slightly lift it
3. Insert the thin tip of your bottle into the filling hole
4. Pour your e-liquid
5. Carefully close the strip

Careful, if you use a new cartridge, wait for some minutes before being vaped so the new coil is correctly primed with e-liquid.

The filling of the cartridge on Voopoo's VMate E2 podmod

Box contents

• 1 1,500mAh VMate E2 podmod
• 1 VMate Top Fill Cartridge with a 0.7ohm sealed coil (pre-installed)
• 1 VMate Top Fill Cartridge with a 0.4ohm sealed coil
• 1 USB-C cable
• 1 user guide

The VMate E2 podmod is made by Voopoo.

Box contents of Voopoo's VMate E2 podmod