Innokin Coolfire PZPulse Podmod

Introducing the Coolfire PZPulse podmod from Innokin, designed for all types of vapers. This electronic cigarette is portable, easy to use, and durable thanks to its IP68 certification (dust and water protection).

This podmod offers indirect inhaling with a power output ranging from 6 to 80 watts, as well as a built-in battery with a capacity of 2,400 mAh.

The kit also includes a PZP cartridge with a magnetic connector and a capacity of 5.5ml.

Its PZP Max plug-n-play coils are designed for DTL or RDL performance. With its easily adjustable airflow, you can experiment with different types of vaping.

Innokin's Coolfire PZPlus podmod

Optimal ergonomy

The Coolfire PZPulse podmod from Innokin combines comfort, ease of use, and robustness. With its compact dimensions of 119x44x31mm, weight of 165g, and zinc alloy construction, the kit is easy to handle.

IP68 certified, the mod is resistant to water and dust particles.

Its main front panel is made from:

• A fire switch
• A 96-inch curved TFT screen
• Two adjustment buttons (- or +)
• A 2A USB-C fast charging port

Handling of Innokin's Coolfire PZPlus podmod

The functioning of a Coolfire PZPulse kit

How to make your Coolfire PZPulse work? To turn your podmod on or off, simply press the fire switch 3 times quickly.

The information displayed on the 0.96" curved TFT screen is as follows, from top to bottom:

1. The lock status of the podmod
2. The remaining battery level in %
3. The power output in watts
4. A puff counter
5. Information about the coil

To adjust the power (6 to 80 watts), simply press and hold one of the two adjustment switches until the value starts flashing. Then use the '+' or '-' buttons to select the desired power (always follow the recommended values for your coil).

The curved 0.96" TFT screen of Innokin's Coolfire PZPlus podmod

Please note that there is a sliding switch on the side of your podmod, which is very useful for quickly locking and unlocking your mod.

The locking switch of Innokin's Coolfire PZPlus kit

A 2,400mAh built-in battery

In its Coolfire PZPulse kit, Innoking chose a rechargeable built-in battery with a 2,400mAh battery.

Its curved TFT screen informs you of its battery level:

1. Red: battery lower than 10%
2. Orange: battery between 10 and 30%
3. Green: battery between 30 and 100%

In case you have a low battery, you only have to use the fast USB-C 2A recharging cable (included in the box) to recharge it. To do this, plug it into the dedicated port and connect it to an electrical outlet or computer equipment.

The USB-C port of Innokin's Coolfire PZPlus kit

The Coolfire PZPulse cartridge

This cartridge, designed for the Coolfire PZPulse podmod, attaches to your mod with a magnetic connector. It has a 5.5ml tank with a top-fill system.

Its airflow is easily adjustable, and its drip tip has a wider opening for easier DL or RDL draws.

As for the cartridge coils, you will need to use Innokin's PZP Max coils.

Innokin's Coolfire PZPulse cartridge

The PZP Max coils

As previously mentioned, the Coolfire PZPulse cartridge only works with Innokin PZP Max Coil coils. These are plug-and-play coils that are very easy to remove or install.

Two coils are included in your Coolfire PZPulse kit box:

• One 0.4 ohm PZP Max coil: to be used between 40 and 60 watts for direct inhaling vaping
• One 0.2 ohm PZP Max coil: to be used between 60 and 80 watts for more direct inhaling vaping

If your coil is worn out, here are the steps to follow to change it:

1. Remove the cartridge from the Coolfire PZPulse podmod
2. Remove the worn-out coil from the center of the cartridge
3. Take a new coil and soak it with a few drops of e-liquid
4. Insert the new coil into your cartridge in the designated slot
5. Put the cartridge back on the magnetized connector of your Coolfire PZPulse podmod
6. Wait 5 to 10 minutes for the coil to prime

An adjustable airflow

The airflow setting is made by the top of the cartridge through a rotative ring.

According to the vapor density desired, you'll have the opportunity to precisely set the opening.

As a reminder: the more the airflow ring is open, the more airy the vape!

The sliding button to set the airflow of Innokin's Coolfire PZPulse cartridge

A top filling for 5.5ml of e-liquid

With a 5.5ml tank, the cartridge presents a great e-liquid capacity.

Filling is done using a top-fill system, i.e., from the top. The hatch is located on the front with a black silicone tab.

Here are the steps to follow to quickly charge this 5.5ml tank:

1. Locate the black silicone tab at the front of your cartridge
2. Lift this tab
3. Insert the tip of your bottle into the filling hole
4. Squeeze your bottle slightly to allow the e-liquid to flow
5. Put the black silicone tab back in place

As a reminder, wait a few minutes before vaping if you are using a new coil.

The filling of Innokin's Coolfire PZPulse cartridge

Box contents

• 1 Coolfire PZPulse mod
• 1 PZPulse cartridge with RDL drip tip
• 1 pre-installed 0.4ohm PZP Max coil
• 1 0.2ohm PZP Max coil
• 1 USB-C cable
• 1 user guide

The Coolfire PZP Pulse podmod is made by Innokin.

Box contents of Innokin's Coolfire PZPulse podmod