MPV Aviator Nano Podmod

Here is this all-in-one kit that fits in the palm of your hand. Despite its miniature size, it packs an 850mAh battery and is capable of delivering 10 to 15W of power.

Its 2ml cartridge functions with removable coils, which produce a rather tight draw with an indirect inhale (MTL).

MPV’s Aviator Nano podmod

A design of Aviator Nano podmod

The Aviator Nano podmod definitely stands out from the crowd thanks to its tiny size!

MPV has managed to fit a built-in battery of 850mAh into this compact e-cigarette, barely measuring 39 x 73 x 15.5mm. Therefore, the device will fit into your pocket with ease, and you might forget it's there as well, as it only weighs 41g.

And if you want to keep your Aviator Nano close at hand, you’ll be glad to know that MPV has included a handy neck strap in its kit. Loop it through the notch on the podmod’s side, just above the USB port.

Handling MPV’s Aviator Nano podmod

The classic magnetic connector

Inserted into the body of the e-cig, the 2ml Aviator Nano cartridge is also held in place by a magnetic connector system, a distinctive feature of the podmod format.

Not only will your tank be well protected in its housing, but it can also be quickly clipped on and off, allowing you to alternate between cartridges as needed to easily vary e-liquid flavors!

The magnetic connector of MPV’s Aviator Nano podmod

A fully automatic operation

The Aviator Nano podmod is incredibly easy to use, you just have to inhale on the mouthpiece to vape!

There is nothing to set up or configure. There are no switches either. Everything is pre-set to produce a great indirect inhale (Mouth-To-Lung vaping), thanks in part to the 1.0ohm Aviator Nano coil inside the podmod’s cartridge. The feeling you get when inhaling is close to the one you’d get with a classic cigarette.

The podmod automatically adjusts the power output from 10 to 15W.

A charge in USB-C

The transparent shell of the Aviator Nano podmod has an LED that tells you how much battery is left.

If the LED is green, that means there’s more than 5% of battery left. When the time comes, you can recharge your battery using the USB-C cable included in the kit.

The USB-C port is located beneath the neck strap notch, on the side of the podmod.

The USB-C port of MPV’s Aviator Nano podmod

A 2ml tank

The Aviator Nano podmod uses a cartridge that can hold up to 2ml of e-liquid and contains a removable coil. There’s a 1.0ohm coil already installed in the cartridge when you unbox the kit, that way you can enjoy your podmod right away.

This cartridge produces a rather tight draw, which is ideal for e-liquids with a high nicotine content, nicotine salts or CBD.

The 2ml cartridge of MPV’s Aviator Nano podmod

Interchangeable coils

As we said, there’s a 1.0ohm Mesh coil already installed in the kit’s tank. But after two to three weeks of intense and tasty vaping, this coil will start to wear out. Don't throw away the cartridge, though! You just need to swap the worn-out coil for a new one.

When it's time to change the coil, follow these simple steps :

1. Remove the podmod’s cartridge from its magnetized connector
2. Flip the cartridge to access the underside of the tank
3. Pull out the old coil
4. Soak the new coil with a few drops of e-liquid
5. Insert it where the old one was
6. Fill your tank with e-liquid
7. Put the cartridge back onto its magnetized connector

Wait 5 to 10 minutes before vaping, so that the new coil can prime itself properly

A flawless airflow without any adjusting 

One thing’s for sure, this podmod's ease of use will make your vaping session smooth and hassle-free. This goes for the airflow as well, as you don't need to do a thing.

MPV has designed its podmod with an ideally placed air intake, right beneath the cartridge, on the opposite side of the USB port.

How to fill the cartridge?

Although the 2ml tank holds a decent amount of e-liquid, you'll need to refill it from time to time.

To do so :

1. Remove the cartridge from its magnetized connector
2. Tilt the cartridge to access the silicone tab
3. Lift the silicone tab to access the filling hole
4. Insert the tip of your bottle of e-liquid into this hole
5. Fill up the tank with e-liquid, never to the brim though
6. Close the silicone tab
7. Place the cartridge back onto the podmod's magnetized connector

Remember to wait 5 to 10 minutes for the new coil to prime itself properly.

Filling the cartridge of MPV’s Aviator Nano podmod

Contents

• The Aviator Nano podmod
• 1 Aviator Nano 2ml cartridge (pre-installed)
• 1 Mesh coil of 1.0ohm (pre-installed)
• A neck strap
• A user guide

The Aviator Nano podmod is made by MPV (Master Pro Vape).

The contents of MPV’s Aviator Nano podmod kit