MPV Aviator Nano Podmod

MPV continues to amaze us with its vaping devices, and there’s a new kit in town, the Aviator Nano podmod !

You're bound to love this all-in-one kit that fits in the palm of your hand. Despite its miniature size, it packs an 850mAh battery and is capable of delivering 10 to 15W of power.

Its 2ml cartridge functions with removable coils, which produce a rather tight draw with an indirect inhale (MTL).

MPV’s Aviator Nano podmod

A small kit that packs a punch !

The Aviator Nano podmod definitely stands out from the crowd thanks to its tiny size !

MPV has managed to fit a built-in battery of 850mAh into this compact ecigarette, barely measuring 39 x 73 x 15.5mm. Therefore, the device will fit into your pocket with ease, and you might forget it's there as well, as it only weighs 41g.

And if you want to keep your Aviator Nano close at hand, you’ll be glad to know that MPV has included a handy neck strap in its kit. Loop it through the notch on the podmod’s side, just above the USB port.

Handling MPV’s Aviator Nano podmod

The classic magnetic connector

The Aviator Nano cartridge fits perfectly into the e-cigarette’s body and is held in place by a magnetic connector, like many podmods.

Not only is the tank well protected in its housing, it can also be removed in a flash, allowing you to switch between several cartridges or e-liquid flavours if you wish !

Feel free to get one or several spare Aviator Nano cartridges from our website!

The magnetic connector of MPV’s Aviator Nano podmod

A fully automatic operation

The Aviator Nano podmod is incredibly easy to use, you just have to inhale on the mouthpiece to vape !

There is nothing to set up or configure. There are no switches either. Everything is pre-set to produce a great indirect inhale (Mouth-To-Lung vaping), thanks in part to the 1.0ohm Aviator Nano coil inside the podmod’s cartridge. The feeling you get when inhaling is close to the one you’d get with a classic cigarette.

The podmod automatically adjusts the power output from 10 to 15W.

A fast and easy charge

The transparent shell of the Aviator Nano podmod has an LED that tells you how much battery is left.

If the LED is green, that means there’s more than 5% of battery left. When the time comes, you can recharge your battery using the USB-C cable included in the kit.

The USB-C port is located beneath the neck strap notch, on the side of the podmod.

The USB-C port of MPV’s Aviator Nano podmod

A 2ml tank

The Aviator Nano podmod uses a cartridge that can hold up to 2ml of e-liquid and contains a removable coil. There’s a 1.0ohm coil already installed in the cartridge when you unbox the kit, that way you can enjoy your podmod right away.

This cartridge produces a rather tight draw, which is ideal for e-liquids with a high nicotine content, nicotine salts or CBD.

The 2ml cartridge of MPV’s Aviator Nano podmod

Interchangeable coils

The Aviator Nano cartridge's interchangeable coils will save you a lot of money !

As we said, there’s a 1.0ohm Mesh coil already installed in the kit’s tank. But after two to three weeks of intense and tasty vaping, this coil will start to wear out. Don't throw away the cartridge, though ! You just need to swap the worn-out coil for a new one.

You can buy a pack of Aviator Nano coils on our website.

When it's time to change the coil, follow these simple steps :

1. Remove the podmod’s cartridge from its magnetised connector
2. Flip the cartridge to access the underside of the tank
3. Pull out the old coil
4. Soak the new coil with a few drops of e-liquid
5. Insert it where the old one was
6. Fill your tank with e-liquid
7. Put the cartridge back onto its magnetised connector

Wait 5 to 10 minutes before vaping, so that the new coil can prime itself properly

A flawless airflow without any adjusting 

One thing’s for sure, this podmod's ease of use will make your vaping session smooth and hassle-free. This goes for the airflow as well, as you don't need to do a thing.

MPV has designed its podmod with an ideally placed air intake, right beneath the cartridge, on the opposite side of the USB port.

An easy side-fill cartridge

Although the 2ml tank holds a decent amount of e-liquid, you'll need to refill it from time to time.

To do so :

1. Remove the cartridge from its magnetised connector
2. Tilt the cartridge to access the silicone tab
3. Lift the silicone tab to access the filling hole
4. Insert the tip of your bottle of e-liquid into this hole
5. Fill up the tank with e-liquid, never to the brim though
6. Close the silicone tab
7. Place the cartridge back onto the podmod's magnetised connector

Remember to wait 5 to 10 minutes for the new coil to prime itself properly

Filling the cartridge of MPV’s Aviator Nano podmod

Contents

• The Aviator Nano pod
• 1 Aviator Nano 2ml cartridge (pre-installed)
• 1 Mesh coil of 1.0ohm (pre-installed)
• A neck strap
• A user guide

The Aviator Nano podmod is made by MPV (Master Pro Vape).

The contents of MPV’s Aviator Nano podmod kit