Innokin Coolfire Z60 Kit

Our Panda expert shows us every detail of Innokin’s CoolFire Z60 kit in this unboxing video!

Choose Innokin’s CoolFire Z60 kit if you’re looking to start vaping properly or if you want a more modern and upgradeable e-cigarette!

This electronic cigarette is made for everyone. It combines the 60W CoolFire Z60 mod, equipped with a 2,500mAh built-in battery, with the Zlide Top clearomizer of 3 or 4.5ml, which uses the Z-Coils and has a top airflow!

This kit shows that power and performance aren’t just for the most experienced vapers. The kit offers a variety of features and is perfect for both tight MTL and airy RDL vaping.

A modern and upgradeable kit

Through its CoolFire Z60 kit, Innokin offers you an effective way of getting started in the wide world of vaping, whilst allowing you to upgrade your kit depending on your needs!

The CoolFire Z60 kit is 120mm high, 27.2mm wide, and 36.6mm deep. It is compact and discreet, equipped with everything you need to vape without any hassle. Indeed, the mod has a built-in battery, a display screen, adjustment buttons, and a USB-C port, whilst the clearomizer has a top airflow, a 510 drip tip, and an easy-fill system.

Innokin’s CoolFire Z60 kit

A smart mod

Innokin’s CoolFire Z60 kit is first of all a well-crafted 60W electronic mod. It’s high-tech but easy to use at the same time, making it suitable for both beginners and experienced vapers.

Indeed, its 2,500mAh built-in battery, quick USB-C charging, and various innovative vaping modes will delight everyone!

The Fire button of Innokin’s CoolFire Z60 kit

A simple, intuitive, and innovative device!

Thanks to its effective electronic chipset, Innokin’s CoolFire Z60 kit can provide vapers with performance and security at all times. Browse through the various menus and settings using the small adjustment buttons and display screen. The mod can reach a maximum power of 60 watts. The vaping modes are as follows:

• COIL +: this mode preserves your coil’s lifespan, resetting it after each puff 
• WATTAGE: the standard variable wattage mode allows you to manually adjust the power output from 5 to 60W
• REFRESH: this mode really brings out your e-liquid’s flavors during the next few puffs, by only heating your coil to 40% so that it soaks up more liquid

In addition to these three modes, there’s a ‘Cutoff' setting that lets you adjust the duration of your puffs, from 3 to 18 seconds. There’s also the 'Screen' setting that allows you to fully customize your interface.

The display screen of Innokin’s CoolFire Z60 kit

Finally, in addition to the various electronic protections the chipset has, Innokin has included an On/Off switch beneath the device. 

The On/Off switch of Innokin’s CoolFire Z60 kit

A 2500mAh battery that can be charged via USB-C

The CoolFire Z60 mod has a 2500mAh built-in battery. In other words, there is no need to install or change a battery. Simply charge the mod using the USB-C port on the mod’s front panel, just below the screen and buttons. There’s a USB-C cable in the kit.

You can check the battery’s charge status on the mod's screen.

The USB-C port of Innokin’s CoolFire Z60 kit

A powerful clearomizer for a complete setup

Innokin has decided to include its high-quality Zlide Top clearomizer in the CoolFire Z60 kit. 

This clearomizer has a diameter of 24.5mm and a tank of either 3 or 4.5 ml offering an MTL or RDL experience. It works with the famous Z-Coils and uses a top airflow system that’s both simple and safe!

The Zlide Top clearomizer in Innokin’s CoolFire Z60 kit

The famous Z-Coils are still in the game!

Innokin is not the kind of manufacturer that offers new coils with each release. It prefers to rely on its tried-and-tested coils. That's why the Zlide Top clearomizer - and therefore the CoolFire Z60 kit - is compatible with the entire range of Z-Coils!

The kit includes :

• One 0.6ohm DuoPrime Z-Coil, which is pre-installed in the clearomizer and should be used between 9 and 13 watts, for quality and long-lasting MTL vape
• One 0.3 ohm Z-Coil, to be used from 30 to 40 watts for an RDL vape.

To change your Z-Coil:

1. Unscrew the clearomizer from the CoolFire Z60 mod
2. Turn it over (making sure the air intakes are closed)
3. Unscrew its lower part
4. Pull out the old coil
5. Grab a new coil and soak its cotton wick with a few drops of e-liquid
6. Insert it where the old one was
7. Screw the clearomizer’s lower part back on, then screw it back on the CoolFire Z60 mod

The Zlide, now available with a top airflow!

The Zlide Top clearomizer is the only one of the Zlide family to offer an adjustable airflow system. This is a much handier mechanism that will prevent any e-liquid leaks!

These wide air intakes are cleverly machined and have a unique look. They are tapered so as to offer a precise and permissive adjustment.

Innokin’s Zlide Top clearomizer can offer a tight, indirect inhale (MTL) and an airier restrictive direct inhale (RDL)!

The air intakes of the Zlide Top clearomiser

An easily and safely filled 3 or 4.5ml tank 

The Zlide Top clearomizer that equips the CoolFire Z60 kit features two types of removable Pyrex tanks:

• A straight Pyrex tank of 3ml, pre-installed on the clearomizer
• A rounded 4.5ml Pyrex tank

Whether you opt for a tight or airy vape, you’ll have plenty of juice to keep you going! Add to this a quick, simple, and secure top-fill system, and you’re ready for a great vaping session.

To fill the Zlide Top clearomizer tank, you must:

1. Slide the top cap outwards. There’s a small arrow engraved on the top cap that shows you in which way you should push
2. Insert the tip of your bottle of e-liquid into the small hole lined with silicone
3. Fill with e-liquid, but never to the brim!
4. Slide the top cap back into its place to close it
5. Wait 5 to 10 minutes for the coil to soak up enough e-liquid
6. Vape!

The top-fill system of the Zlide Top clearomizer from Innokin’s CoolFire Z60 kit

Contents

• The CoolFire Z60 mod
• The Zlide Top clearomizer
• A spare bubble Pyrex tank of 4.5ml
• A spare 510 drip tip
• One pre-installed 0.6Ω Z-Coil
• One 0.3Ω Z-Coil
• A USB-C cable
• A set of spare parts
• A user guide

The CoolFire Z60 kit is manufactured by Innokin.

Contents of the box of Innokin’s CoolFire Z60 kit