Hellvape Dead Rabbit Solo RTA Atomizer

Discover a simplified version of the Dead Rabbit V3 RTA: The Dead Rabbit Solo RTA atomizer with a single coil and postless deck!

Are you an expert vaper who wishes to start in the rebuildable world? With its Dead Rabbit Solo RTA atomizer, the Hellvape brand offers a simplified version of the Dead Rabbit V3 RTA. Directly meant for expert vapers and DL enthusiasts, this atomizer will give you an exceptional flavor rendering throughout the 4ml bulb tank.

Available in several colors, you'll be making the perfect match for your electronic or mechanical mod.

It has a diameter of 24 mm and is equipped with an 810 drip tip. In addition, it has an original top airflow, offering you a leak-free vape!

Hellvape's Dead Rabbit Solo RTA atomizer on the Vaporesso's Armour S mod

The design of Dead Rabbit Solo RTA

Hellvape offers an atomizer that will enhance your mod. Available in several colors, it will match most mods thanks to its 510 gold-plated connector.

You'll find in this box two Pyrex, one straight and one bulb, so you can enjoy both style and volume.

With a height of 37.4mm and a width of 25.5mm, this atomizer will impress with its deck and its notched airflow ring. The rabbit carved on the chamber and the large top airflow bring originality and elegance to the Dead Rabbit Solo RTA. You'll find a black 810 drip-tip no matter the color you choose.

Hellvape's Dead Rabbit Solo RTA atomizer

A postless deck

Hellvape offers you the perfect deck to discover the world of rebuildables. Its single-coil and postless build deck will accommodate coils of all diameters, with a pleasant working surface.

For good flavor rendering, you will find three oval holes allowing good air circulation.

Here are a few recommendations to help you assemble your coil easily:

• Center the coil precisely. You will have about 2mm of space below, allowing for proper alignment with the airflow
• Place your cotton and leave about 12mm of wick sticking out
• Fan the cotton with a pointed tool
• Slide the wicks into the grooves without pushing them down to the bottom
• Make sure the cotton is thoroughly soaked

Thanks to the included accessory kit, which contains a screwdriver for tightening all the screws, all you have to do is assemble your coil and cotton.

The single coil deck of Hellvape's Dead Rabbit Solo RTA atomizer

A top airflow

Hellvape's Dead Rabbit Solo RTA will make you forget all about leaks. With an airflow on the high part, just above the tank, you'll have a vape with no worries about any trickle of e-liquid.

To manage the airflow, you only need to slip the large notched airflow ring of this atomizer to find the ideal position and to go from a direct inhaling vape (DL) to a tighter vape in restrictive direct inhaling (RDL). The more the airflow is open, the more air will go inside the atomizer and give an airy vape.

The airflow ring of Hellvape's Dead Rabbit Solo RTA atomizer

A simplified filling

Hellvape has bet on simplicity for the filling of the tank. Thanks to a top filling with a sliding top-cap system, your fillings in e-liquids will be made in no time. A small red arrow will show you where you need to push.

The Dead Rabbit Solo RTA atomizer is sold with two Pyrex. The first is straight and can hold up to 2ml of your e-liquid, while the bulb version offers a capacity of 4ml.

For your first filling, follow these suggestions:

• Push the top cap in the same direction as the red arrow
• Insert the thin tip of your e-liquid into the hole
• Pour your e-liquid
• Close the top cap

Filling of Hellvape's Dead Rabbit Solo RTA atomizer

Contents of the box

• 1 Dead Rabbit Solo RTA atomizer
• 1 straight 2ml Pyrex (pre-installed)
• 1 bulb 4ml Pyrex
• 1 flat screwdriver
• 4 screws
• 1 set of gaskets
• 1 user guide

The Dead Rabbit Solo RTA atomizer is made by Hellvape

Contents of the box of Hellvape's Dead Rabbit Solo RTA atomizer