Aspire Flexus Stik Podmod

The Flexus Stick by Aspire, for a vape in all easiness

Accessible to all vapers types, but especially intended for novices and beginners, discover the small electronic cigarette Flexus Stik by Aspire!

Discover this pod mod in tubular format, as easy to carry as to use! With a built-in 1200mAh battery and a 3ml PCTG cartridge, it promises long-lasting vaping.

The Flexus Stik podmod by Aspire

The design of Flexus Stik podmod

Discover its practical size in a miniature and tubular shape. All in all, the Flexus Stik pod is only 120mm high and 22mm in diameter. It also weighs in at a feathery 56 grams.

But more than its ergonomic and easily transportable format, you'll love its design in pure anodized aluminum alloy.

Handling Aspire's Flexus Stik podmod

A 1,200mAh built-in battery

Like any self-respecting podmod, the Flexus Stik combines a built-in battery (in this case, 1,200mAh) with a cartridge (in this case, PCTG, 3ml). These two elements are linked together by an efficient system of magnets.

Already simple in its constitution, the Flexus Stik kit also plays the card of simplicity in its operation, the vape is pre-set for ease of use, fully secured for reliability, and ingeniously framed by LEDs for clarity.

In other words, this electronic cigarette has everything to please beginners!

The magnetic connection of Aspire's Flexus Stik podmod

How does the Flexus Stik podmod work?

A pod mod electronic cigarette is best known for its ease of use. And the Flexus Stik podmod sets the bar even higher!

• Firstly, by offering a fire button (or 'fire' or 'switch') positioned at the very bottom of your e-cigarette. A good way to avoid accidental triggers!
• Then, by taking the famous ultra-secure chipset of Aspire, the ASP. It embeds no less than 6 electronic protections!
• Finally, by remaining infinitely simple, with no screen and no adjustment buttons, the Flexus Stick podmod only offers three pre-recorded power levels, distinguishable thanks to a system of LED indicators at the very bottom of the device, near the fire button.

The three power levels offered:

• High: green LED
• Medium: blue LED
• Low: red LED

The switch with LED indicators of Aspire's Flexus Stik podmod

A 1200mAh built-in battery that charges quickly: USB-C port

The Flexus Stik podmod works so well and for so long (up to 2 days according to the manufacturer), thanks to its powerful built-in battery with 1,200mAh autonomy. And, if it recharges so quickly and easily, it's thanks to its ingenious USB-C port!

Accessible from the bottom of your electronic cigarette, this 1A connector is designed to receive the cable supplied in your box. All that's left to do is to connect it to an external power source!

The USB-C recharging port of Aspire's Flexus Stik podmod

The Flexus Stik cartridge

The Flexus Stik cartridge must be clipped onto your Flexus Stik built-in battery. It's easy to do; both the cartridge and the pod base have magnets. They attract each other immediately, and the cartridge is in place in just a few seconds!

The Flexus Stik cartridge is robust; it's made of PCTG! It's also equipped with a 3ml tank! In addition, it accommodates the manufacturer's famous AF coils, reveals a clean and easy filling system, and even allows the adjustment of airflows!

Its great asset? It has a 510-type drip tip.

The 3ml PCTG cartridge of Aspire's Flexus Stik podmod

The AF coils from Aspire

In your cartridge, you will install the manufacturer's AF coils. This change should be made approximately every two to three weeks, depending on your use.

But you won't need them right away! Your Flexus Stik podmod comes with two AF coils:

• AF Coil 1 ohm: for 12 to 15 watts of use
• AF Coil 0.6 ohm: for 15 to 18 watts of use

N.B.: These coils are suitable not only for any type of e-liquid (even with high nicotine content) but also for e-liquids with nicotine salt or CBD.

However, you will prefer a high PG ratio, i.e. e-liquids composed of 50% or more of propylene glycol.

How to install or change your coil?

1. Unclip the cartridge from the podmod's magnetic base
2. Turn it over
3. Take a new coil out of its packaging and soak it with a few drops of e-liquid to prime it
4. If a replacement, remove the old coil from its place and then place the new one
5. During the first installation, place this AF coil in the center of the tank by pushing well
6. Replace the cartridge on the magnetic base of the podmod

The airflow of Flexus Stik podmod

On the Flexus Stik podmod by Aspire, the air intake is ingeniously thought out; it relies not only on the small windows present on the body of your electronic cigarette but also on the cartridge itself!

We explain, that to adjust your draw, it's not through the air intake that you will proceed, but simply through the cartridge, by turning it from right to left until you find your ideal airflow!

The airflow system of Aspire's Flexus Stik podmod

A 3ml PCTG cartridge to fill from the bottom

The cartridge, i.e, the tank, of your Flexus Stik podmod is made of PCTG material, which makes it very resistant to everyday challenges. In addition, this cartridge has a capacity of 3ml, the perfect volume to avoid the hassle of constantly refilling your tank!

Moreover, refilling will never be a difficulty on the Aspire Flexus Stik podmod. It's simply done through the bottom of the cartridge:

1. Unclip the cartridge from the podmod's magnetic base
2. Turn it over
3. Lift the silicone tab present
4. Insert the tip of your e-liquid bottle into the orifice
5. Refill (never to the brim)
6. Replace the tab, then the cartridge on the podmod's magnetic base
7. Wait about ten minutes for a perfect priming of your coil

The filling of Aspire's Flexus Stik podmod

Box contents of the Flexus Stick podmod

• A built-in battery Flexus Stik - 1200mAh
• A Flexus Stik cartridge
• AF's coil 1Ω
• AF's coil 0.6Ω
• A recharging USB-C cable
• A user guide

The Flexus Stik podmod is made by Aspire.

The box contents of Aspire's Flexus Stik podmod