OXVA Oneo Pro Podmod

Is the OXVA Oneo Pro podmod made for you? Discover it in this unboxing!

OXVA offers the Pro version of its Oneo podmod, a kit as compact as it is powerful!

This electronic cigarette has a built-in battery with a 2,100mAh capacity, rechargeable via USB-C.

A color TFT screen gives you access to power settings, from 5 to 40W.

This podmod is specially made to hold the Oneo Pro cartridges from the manufacturer. These are equipped with a sealed coil and a 4ml tank.

OXVA's Oneo Pro podmod

The design of Oneo Pro podmod

The Oneo Pro podmod is a compact e-cigarette measuring 107x33.5x24.5mm and weighing 122g.

A cap protects the cartridge while complementing the device's rounded-edge design.

The Oneo Pro podmod features:

• A power button
• A 0.96-inch color TFT screen
• A USB-C port for charging
• An airflow button to customize the airflow

Handling of OXVA's Oneo Pro podmod

Adjustable power

The Oneo Pro podmod's screen displays various pieces of information:

• Battery level
• Coil value
• Selected power level

To adjust the power to your liking, press the power button three times in a row. Then press the button again to cycle through the wattage settings until you reach your desired power level, up to 40 watts.

The Oneo Pro podmod features an automatic draw system. In other words, all you have to do is inhale through the 510 drip tip to vape!

The screen of OXVA's Oneo Pro podmod

A 2,100mAh battery life

In terms of battery life, the Oneo Pro podmod features a built-in 2,100mAh battery, providing extended usage time.

This battery charges easily and quickly via the USB-C port located on the bottom of the kit. Track the charging progress in real time on your podmod's screen.

OXVA includes a compatible USB-C cable in the box.

The USB-C port of OXVA's Oneo Pro podmod

The Oneo Pro Cartridge

The Oneo Pro kit comes with two cartridges, one of which is already installed on the podmod.

Each has a 4ml e-liquid capacity and contains a sealed coil.

The cartridge connects quickly and easily to the podmod thanks to its magnetic base.

Note that this podmod is also compatible with Oneo XVA cartridges. However, the cap will not be compatible in this case.

The magnetic connection between the cartridge and OXVA's Oneo Pro podmod

Choose your draw

Depending on the type of vape experience you’re looking for, select the Oneo Pro cartridge that’s right for you from the two provided:

• Oneo Pro cartridge with a sealed 0.8ohm coil: for a tight draw in indirect inhaling (MTL), to be used between 14 and 18W
• Oneo Pro cartridge with a sealed 0.4ohm coil (pre-installed): for a lighter, airier vape with restricted direct inhalation (RDL), to be used between 28 and 34W

After a few weeks of use, the coil will show some signs of wear (loss of flavor, slight burnt taste). At that point, it will be time to replace the cartridge with a new one.

OXVA also allows you to adjust the airflow via an airflow control button located on one side of the podmod.

Adjust the airflow openings to open or close them as needed, allowing you to quickly switch from a tight draw to a slightly airier vape.

OXVA's Oneo Pro cartridge

How to fill your tank?

To fill the 4ml tank with e-liquid, follow the steps below:

1. Remove the cap
2. Lift the silicone tab on the side of the cartridge
3. Insert the narrow tip of your bottle into the filling hole
4. Pour in the e-liquid
5. Close the tab
6. Replace the cap

Is your cartridge new? Wait a few minutes before vaping to allow the coil to properly saturate with e-liquid.

Filling OXVA's Oneo Pro podmod

Box contents

• 1 2,100mAh Oneo Pro podmod
• 1 0.4ohm Oneo Pro cartridge (pre-installed)
• 1 0.8ohm Oneo Pro cartridge
• 1 USB-C cable
• 1 user guide

The Oneo Pro podmod is made by OXVA.

Box contents of OXVA's Oneo Pro podmod