Innokin Zenith Pro 2 Clearomizer

Innokin comes back with a Pro 2 version of the Zenith, a versatile clearomizer enabling you to vape in indirect inhaling (MTL) and restrictive direct inhaling (RDL).

With a 4.5ml straight tank, the Zenith Pro 2 is specially made for the Z-Coils by Innokin.

With top fill and top airflow, this clearomizer is meant for all types of vapers looking for performing equipment and a compromise between flavors and vapor.

With a 25.5mm diameter, it will match all mods with a standard 510 connection.

The Zenith Pro 2 clearomizer with Lost Vape's Thelema Q200 Pro mod

A refined look

The Zenith Pro 2 presents a compact format with a 55mm height (with the drip tip) for a 25.5mm diameter.

Innokin bets on a stainless steel structure with a sober design, enabling this clearomizer to be associated with most mods.

The base of the Zenith Pro 2 and its top cap are shaped with beveled edges for a clean look.

Innokin's Zenith Pro 2 clearomizer

The Z-Coil coils

Innokin joins two Z-Coils in the Zenith Pro 2 box.

Select the one suiting you according to the desired vape type:

• 0.8ohm Z-Coil (pre-installed): to use between 15 and 18 watts, for a tight draw in indirect inhaling (MTL)
• 0.3ohm Z-Coil: to use between 30 and 40 watts, for an airier vape in restrictive direct inhaling (RDL)

After two to three weeks of use, the coil will start to show some wear signs (loss of flavor, light burnt taste).

It will be time to change to a new one.

For this:

1. Unscrew the bottom part of the Zenith Pro 2
2. Pull on the used coil to take it off
3. Soak a new coil with some e-liquid drops
4. Insert the latter into the compartment in place of the old one
5. Screw the clearomizer back on
6. Fill the tank with e-liquid
7. Wait for some minutes before vaping so the coil is correctly primed

Please note that the vape experience can also be changed thanks to the two drip tips included.

Indeed, the pre-built MTL mouthpiece can be replaced with the RDL drip tip included in the box.

A Pro 2 version with an efficient top airflow

For the airflow, Innokin chose air intakes on the clearomizer's top part.

The Zenith Pro 2 has an airflow ring enabling you to free the three small holes for a tight draw (MTL) or the large window for an even airier vape (RDL).

The airflow of Innokin's Zenith Pro 2 clearomizer

A 4.5ml top-fill tank

The Zenith Pro 2 has a straight Pyrex with a 4.5ml capacity.

Please note that a spare tank is included in the box.

When you need to fill your clearomizer with e-liquid, no need to take it out of the mod.

Indeed, the Zenith Pro 2 benefits from a top-filling system.

For this, you only need to:

1. Push the top cap to the mark
2. Insert the bottle tip into the filling hole
3. Softly pour your e-liquid
4. Push the top cap back to its place

Is your coil new? Wait for some minutes before vaping so it's correctly primed with e-liquid.

Filling Innokin's Zenith Pro 2 clearomizer

Box contents

• 1 4.5ml Zenith Pro 2 clearomizer
• 1 0.8ohm Z-Coil (pre-installed)
• 1 0.3ohm Z-Coil
• 1 spare Pyrex
• 1 set of spare seals
• 1 user guide

The Zenith Pro 2 clearomizer is made by Innokin.

Box contents of Innokin's Zenith Pro 2 clearomizer