Geekvape Z Fli 2 Clearomizer

From elegance to big cloud production, the Z Fli 2 clearomizer combines design and performance. Discover this sub-ohm clearomizer in this video.

Geekvape is back with a second version of its Z Fli, a sub-ohm device clearly designed for direct inhaling (DTL).

Designed for a very airy vape, this clearomizer still has a round Pyrex tank with a capacity of 5.5 ml.

The manufacturer has kept the Flip system that made the first version so successful, allowing the top cap to be opened quickly and easily.

The Z Fli 2 is compatible with the Z Series range of coils and features a leakproof top airflow.

The Z Fli 2 clearomizer with Geekvape's Aegis Legend 5 mod

Z for Zeus, Fli for Flip!

With version 2 of the Z Fli, Geekvape retains all the advantages of its big brother, namely a sophisticated design, a 5.5 ml Pyrex bulb, and the essential top cap with valve!

In terms of improvements, the clearomizer is equipped with an even more effective chimney, with a Damascus steel finish.

With a height of 51.5 mm and a standard 510 pin, this clearomizer will connect to all your mods with a minimum diameter of 24 mm.

The clearomizer is equipped with an 810 drip tip, designed for a very cloudy draw when inhaling directly.

Geekvape's Z Fli 2 clearomizer

The Z Series coils

Just like the first version, the Z Fli 2 is specially designed to accommodate Z Series coils.

Geekvape includes two in the clearomizer box:

• 1 0.15ohm Z XM coil (pre-installed): to be used between 70 and 85W, for a very airy vape
• 1 0.4ohm Z XM coil: to be used between 50 and 60W, for a slightly less restrictive draw

How to change your coil?

Is your coil reaching the end of its life? Are you starting to notice a loss of flavor or even a slight burnt taste?

Then it's time to change it for a new one!

For this:

1. Unscrew the bottom part of the clearomizer
2. Take the used coil out by pulling on it
3. Soak a new coil with some e-liquid drops
4. Insert it in its compartment in place of the old one
5. Screw the bottom part back
6. Wait for some minutes before vaping so the new coil is correctly primed with e-liquid

A leakproof top airflow

Always with the aim of offering you an effective and leakproof system, Geekvape has equipped its Z Fli 2 with a top airflow.

In other words, the airflow is adjusted from the top of the clearomizer.

Also, to easily and quickly vary the type of draw, simply turn the airflow ring located just below the top cap.

The more you open the air intake, the cloudier your vape will be!

The airflow of Geekvape's Z Fli 2 clearomizer

The increasingly effective 'Flip' system

Geekvape has retained the clever system of opening the top cap with a simple push, allowing you to charge your tank in a snap!

Simply press the red mark on the top of the clearomizer to access the two filling holes.

Take your dropper bottle and fill your 5.5 ml tank by following these steps:

1. Open the top cap of the Z Fli 2
2. Insert the tip of your bottle into one of the two holes
3. Pour in your e-liquid, taking care not to spill any into the central hole of the chimney
4. Close the top cap

Reminder: if your coil is new, wait 5 to 10 minutes before vaping.

The filling of Geekvape's Z Fli 2 clearomizer

Box contents

• 1 5.5ml Z Fli 2 clearomizer
• 1 0.15ohm Z XM coil (pre-installed)
• 1 0.4ohm Z XM coil
• 1 spare Pyrex
• 1 set of spare pieces
• 1 user guide

The Z Fli 2 clearomizer is made by Geekvape.

Box contents of Z Fli 2 clearomizer by Geekvape