Wotofo Squonk Profile Mod
A single battery 80W mod for BF that can be turned into a dual-battery 200W mod!
-
Diameter30mm
-
Volume7ml
-
Maximum power80 or 200W
-
Brand
Thanks to the Squonk Profile mod by Wotofo, you don't need to choose between your two favorite teams, squonkers versus non-squonkers!
This beautiful electronic can be used in dual 18650 batteries (not provided) for a maximal power of 200 watts, like prowess in BF mode, so in a single 18650 battery operation (not included) with a 7ml squonk bottle next to it, for a maximum power of 80W!
Incredible versatility, only possible with the Squonk Profile by Wotofo!
The Squonk Profile mod associated with the Tauren Max RDA dripper
An atypical look
Each face of your Squonk Profile mod reserves beautiful surprises. Thus, while its main front is occupied by a beautiful screen, but also effective adjustment buttons, its back side prefers to adopt a transparent look of the most endearing.
The Squonk Profile mod by Wotofo, front view
At 93.85mm high, 44.4mm wide, and 30mm deep, and weighing in at a hefty 135 grams, Wotofo has managed to make it compact, robust, and stylish!
Entirely made in zinc alloy quality, the Squonk Profile mod promises flavorful surprises. Screw your beautiful atomizer (until 30mm of diameter maximum) on its 510 connector and go on an adventure!
The Squonk Profile mod by Wotofo, back view
A polyvalent and securitized electronic, 80W or 200W!
Where your Squonk Profile mod excels is undoubtedly in the versatility of its use. In addition to being perfectly safe (short-circuits, under-voltage, overheating, polarity reversals, etc.) thanks to the NexChip by Wotofo chipset, your electronics will be able to offer you two very different operating modes:
- A working up to 200 watts, only possible in double batteries 18650 use (not provided)
The 200W working of the Squonk Profile mod by Wotofo
- A functioning up to 80W, specially dedicated to bottom-feeding, so with a single 18650 battery (not provided) and a 7ml squonk bottle provided in the box
The 80W functioning of the Squonk Profile mod by Wotofo
Of course, no matter the chosen functioning, your Squonk Profile mod will display all the indispensable information via a wonderful TFT screen of 0.96", and two little adjustment buttons '+' and '-' situated below.
A single or dual-battery mod made for squonking!
As you can see, your Squonk Profile mod will be able to offer you two operating modes, 200W or 80W. These two options will depend mainly on your power supply mode.
Double batteries for up to 200W
For example, if you want to use your mod to the maximum of its performance, until 200W, you need to remove the squonk bottle already integrated inside the removable back panel, and integrate two 18650 batteries (not included). Note that a large tab will allow you to put them on and take them off as quickly as possible.
The double-battery housing of the Squonk Profile mod by Wotofo, for 200W working
A single-battery operation for BF use, with a 7ml squonk bottle
On the other hand, if you are only interested in bottom-feeding, you can leave the 7ml squonk vial already in place and insert a single 18650 battery alongside it.
The single-battery housing of the Squonk Profile mod by Wotofo, for 80W working
Already integrated inside your mod, you'll find a generous flexible bottle in polycarbonate (PC) of 7ml capacity. This latter is specially provided to supply coils and your favorite BF dripper, so equipped with the 510 BF pin. For this, you just need to slightly push on it. It will then push the e-liquid in its bottle up into your assembly!
To refill your pretty bottle, you only need to remove it from its place, then unscrew its small cap, to finally insert the tip of your bottle of liquid.
The 7ml squonk bottle filling of the Squonk Profile mod by Wotofo
And, in addition to these two nice surprises, your mod will also be equipped with a USB-C charging port. Combined with the USB-C cable provided in your box, you will have all the cards in hand for a serene vape, always full of energy!
The recharging USB-C port of the Squonk Profile mod by Wotofo
Contents of the box
- A Squonk Profile mod
- A 7ml squonk bottle (pre-installed)
- A recharging USB-C cable
- A user's guide
The Squonk Profile model was made by Wotofo.
Contents of the box of the Squonk Profile mod by Wotofo
Diameter | 30mm |
---|---|
Volume | 7ml |
Maximum power | 80 or 200W |
Battery type | 18650 x1 (or x2) |
Height | 93.8mm |
Material | Zinc alloy |
Width | 44.4mm |
Depth | 30mm |
Mod type | Box |
Batteries included | No |
Weight | 135g |
Mod type | Electronic |
USB charging | Yes |
Chipset | Nexchip |
Chipset version | Wotofo |
Tank | Polycarbonate (PC) |
Connector pin | 510 |