Vaponaute VB26 Kit

Discover the VB26, the SBS kit by Vaponaute, in this unboxing video!

The VB26 is an e-cigarette designed for enthusiasts of airy draw in direct vaping (DL).

It consists of the VB26 mod and the VT26 clearomizer from Vaponaute.

The mod delivers a maximum power output of 80W and is powered by a single 18650 battery (not included).

The clearomizer is specifically designed to accommodate Innokin's PZP Max coils.

Its 4ml straight Pyrex tank is easily filled from the top (top-fill).

Vaponaute's VB26 kit

The design of the VB26 kit

Designed by modder Vaponaute, the VB26 features a design inspired by the world of aviation in a Side-by-Side (SbS) format.

The kit comes in a metal case and includes a Vaponaute keychain.

Made of zinc alloy, this compact e-cigarette measures 112mm high by 27mm wide.

It features a 0.96'' OLED screen that gives you access to all the information you need for a high-quality vaping experience.

Handling of Vaponaute's VB26 kit

An adjustable power up to 80W

Vaponaute lets you control the power setting yourself, depending on the type of coil installed in the VT26 clearomizer.

To do this, press the "+" or "-" buttons simultaneously for one second until the numbers flash on the screen.

You can also lock the kit by pressing the Power button and the "-" button at the same time.

This will prevent vapor production and prevent changes to the power setting.

The VB26 box's chipset includes numerous electronic safety features, such as protection against overheating, short circuits, overcharging, and excessive puff duration.

The screen of Vaponaute's VB26 kit

A capacity of a 18650 single battery

As for battery life, the VB26 is powered by a 18650 battery.

Since no battery is included with the kit, be sure to get one right away!

To insert it, simply unscrew the cap located under the mod, and be sure to insert it with the correct polarity.

The battery's charge level is displayed on the OLED screen.

The single battery compartment of Vaponaute's VB26 kit

Run out of battery power? Use the USB-C cable included in the box and plug it into the port located on the bottom of the mod.

However, we recommend using an external charger whenever possible to recharge your battery, primarily to help preserve its lifespan.

The USB-C port of Vaponaute's VB26 kit

The VT26 clearomizer

The VT26 is a clearomizer specifically designed for an airy vape in direct inhalation (DL).

Compatible with PZP Max coils, it features a top-fill tank with a 4ml capacity.

Its original 510 drip tip can be replaced with the wider-mouth drip tip included in the box.

The VT26 clearomizer of Vaponaute's VB26 kit

Two PZP Max coils included

The VB26 kit comes with two PZP Max coils, designed to be inserted into the VB26 clearomizer.

Choose the one that best suits your vaping style from the following:

• 1 PZP Max coil rated at 0.2 ohm: for a very airy draw, between 60 and 80 watts
• 1 PZP Max coil rated at 0.4 ohm (pre-installed): for a slightly more restrictive draw, to be used between 40 and 60 watts

After two to three weeks of use, the coil will show signs of wear, such as a loss of flavor or even a slight burnt taste.

It will then be time to replace it!

To do so:

1. Remove the VT26 from the mod
2. Unscrew the bottom section of the clearomizer
3. Pull out the used coil to remove it
4. Soak a new coil with a few drops of e-liquid
5. Insert it into its compartment in place of the old one
6. Screw the bottom section of the clearomizer back on
7. Reconnect the VT26 to the VB26 mod
8. Fill the tank with e-liquid
9. Wait 5 to 10 minutes before vaping to allow the new coil to soak up the e-liquid properly

An adjustable top airflow

The VT26's air intakes are located at the top of the clearomizer.

To adjust the airflow, simply rotate the airflow ring: the more you open the vents, the airier your draw will be.

Conversely, the more you restrict the airflow, the tighter your vape will be.

The airflow of the VT26 clearomizer of Vaponaute's VB26 kit

How to fill the tank?

The VT26 clearomizer features a straight tank with a 4ml e-liquid capacity.

Note that a replacement Pyrex tank is included in the kit box.

This tank features a convenient "top-fill" system, meaning it's filled from the top of the clearomizer.

This means you don’t need to remove the VT26 from the mod to refill it with e-liquid.

Simply:

1. Push the clearomizer's top cap down to the mark
2. Insert the narrow tip of your bottle into the opening covered by a silicone membrane
3. Gently pour your e-liquid until the tank is three-quarters full
4. Replace the top cap by pushing it back in the opposite direction

As a reminder, wait a few minutes before vaping if your coil is new.

Filling the VT26 clearomizer of Vaponaute's VB26 kit

Box contents

• 1 80W VB26 mod
• 1 4ml VT26 clearomizer
• 1 0.4ohm PZP Max coil (pre-installed)
• 1 0.2ohm PZP Max coil
• 1 spare 510 drip tip
• 1 USB-C cable
• 1 set of spare pieces
• 1 keyring
• 1 user guide

The VB26 kit is made by Vaponaute. It is sold without batteries.

Box contents of Vaponaute's VB26 kit