Lost Vape Centaurus Nano MTL Clearomizer

The Centaurus Nano MTL is a clearomizer designed for a relatively tight draw with indirect inhalation.

Equipped with a 4ml tank, it is specifically designed to accommodate Lost Vape's UB MTL coils.

Its filling system and airflow ring are located at the top of the clearomizer.

With a diameter of 27mm and a standard 510 pin, it is compatible with most electronic mods on the market.

The Centaurus Nano MTL clearomizer with Lost Vape's Thelema Solo 100 mod

The design of the Centaurus Nano MTL

With this Nano MTL version, Lost Vape retains the metal frame of the Centaurus series clearomizers.

The Centaurus Nano MTL stands out for its straight lines and its tank, which is partially encased in a frame, the openings in which allow you to check your e-liquid level.

At the top, Lost Vape replaces the wide mouthpiece found on the Sub-Ohm versions with a 510 drip tip, which is particularly well-suited for indirect inhalation.

The Centaurus Nano MTL clearomizer measures 51.8mm in height and has a diameter of 27mm.

Its design combines SUS303 stainless steel, POM (polyoxymethylene), and borosilicate glass.

Lost Vape's Centaurus Nano MTL clearomizer

The UB MTL coils

The Centaurus Nano MTL is compatible with Lost Vape's UB MTL coils.

Two coil options are included in the box, both designed for a tight draw with indirect inhalation:

• 1 UB MTL 0.8ohm coil: to be used between 12 and 17W
• 1 UB MTL 1.2ohm coil: to be used between 7 and 11W

After two to three weeks of use, the coil will show signs of wear, such as a loss of flavor or a slight burnt taste.

It will then be time to replace it with a new one.

To do so:

1. Detach the Centaurus Nano MTL clearomizer from your mod
2. Turn it upside down and unscrew the base
3. Remove the used coil
4. Soak the visible cotton parts of your UB MTL coil with a few drops of e-liquid
5. Insert this coil into its compartment in place of the old one
6. Screw the bottom part of the clearomizer back on
7. Fill the tank with e-liquid
8. Connect the clearomizer to your mod
9. Wait a few minutes before vaping to allow the new coil to prime properly

A precise top airflow

The Centaurus Nano MTL features an adjustable airflow control located on the top of the tank.

By rotating the airflow ring, you can open or close the small vents. This allows you to quickly and easily switch from a very tight draw to a slightly less restricted vape, and vice versa.

This top airflow system helps minimize e-liquid leaks through the air intakes.

Lost Vape includes a spare drip tip with a slimmer profile (Spare Slim) in the box, allowing you to further customize your draw.

The airflow of Lost Vape's Centaurus Nano MTL clearomizer

A top-fill tank

The Centaurus Nano MTL has a tank that can hold up to 4ml of e-liquid.

This clearomizer features a convenient top-fill system, so you don’t have to remove it from your mod.

To refill the tank with e-liquid:

1. Slide the top cap (the upper part of the clearomizer) to expose the fill port
2. Insert the narrow tip of your bottle into the designated opening
3. Gently pour in your e-liquid; be careful not to let any spill into the central hole of the airstem
4. Close the top cap

As a reminder, when installing a new coil, wait a few minutes before vaping.

The filling of Lost Vape's Centaurus Nano MTL clearomizer

Box contents

• 1 Centaurus Nano MTL 4ml clearomizer
• 1 0.8ohm UB MTL coil
• 1 1.2ohm UB MTL coil
• 1 Spare Slim 510 drip tip
• 1 spare Pyrex
• 1 bag of spare pieces
• 1 user guide

The Centaurus Nano MTL clearomizer is made by Lost Vape.

Box contents of Lost Vape's Centaurus Nano MTL clearomizer