Aspire H2 Clearomizer

A sub-ohm clearomizer made to combine power, flavors, and big clouds. Discover the Aspire's H2 in this video!

With the H2 (Huracan 2) clearomizer, Aspire has created a device clearly designed for direct inhalation (DL), offering a very airy draw enhanced by an 810-style drip tip.

The H2 is specifically designed to accommodate the manufacturer's BP-F coils, but is also compatible with Aspire's BP Coils.

This clearomizer features a 7ml bulb tank, which is interchangeable with the 6ml straight Pyrex tank included in the box.

With top-fill and top airflow, the H2 offers all the features needed for an intuitive and high-performance vaping experience.

Aspire's H2 clearomizer with Lost Vape's Thelema Q200 Pro mod

The H2 design

The H2 clearomizer measures 52mm of height for a base diameter of 26mm.

It is delivered equipped with a Pyrex in a bulb format with a great e-liquid capacity of 7ml.

Inside the mod, you'll find a replacement tank; this one is upright and has a 6ml capacity.

Aspire has opted for a stainless steel construction and an angular design, allowing you to pair it with even your largest mods.

Aspire's H2 clearomizer

BP-F coils

Designed specifically for sub-ohm vaping, two BP-F coils are included with the H2 clearomizer.

Install the one that suits you best based on the type of draw you’re looking for:

• 0.17ohm BP-F Meshed coil: use between 45 and 55W for a very airy vape
• 0.3ohm BP-F Meshed coil (pre-installed): use between 30 and 40W for a slightly tighter draw

How to replace your coil?

After two to three weeks of use, your coil will show signs of wear, such as a loss of flavor or a slight burnt taste.

You’ll then need to replace it with a new one.

To do this, start by unpacking a new coil, then:

1. Unscrew the bottom section of the H2 clearomizer
2. Pull out the used coil to remove it
3. Soak the new coil with a few drops of e-liquid
4. Then insert it into its slot in place of the old one
5. Screw the bottom section of the clearomizer back on
6. Connect the H2 to your mod
7. Fill the tank with e-liquid
8. Wait a few minutes for the coil to properly saturate with e-liquid
9. Vape away!

A top-airflow clearomizer

When it comes to airflow, Aspire lets you control the airflow rate via an airflow ring located on the top of the H2 clearomizer.

Rotate this ring to open or close the two large air vents: the more air you let in, the airier your vape will be.

Conversely, the more you restrict the airflow, the tighter your draw will be.

The airflow of Aspire's H2 clearomizer

A top-filling system

The H2 clearomizer is equipped with a sliding top cap.

To access the fill port, simply push the top of the clearomizer at the marked spot.

Next, insert the narrow tip of your bottle and gently pour your e-liquid until the tank is three-quarters full.

Finish by pushing the top cap back in the opposite direction to close it.

Reminder: Wait 5 to 10 minutes if you’re using a new coil.

Filling Aspire's H2 clearomizer

Box contents

• 1 7ml H2 clearomizer
• 1 6ml spare Pyrex
• 1 0.3ohm BP-F Meshed coil (pre-installed)
• 1 0.17ohm BP-F Mesh coil
• 1 bag of spare seals
• 1 user guide

The H2 (Huracan 2) clearomizer is made by Aspire.

Box contents of Aspire's H2 clearomizer