Geekvape Z Nano MTL Clearomizer

Geekvape expands its collection of Z Nano clearomizer here with a version clearly meant for enthusiasts of tight draw in indirect inhaling, being in MTL. This type of vape is particularly suited to vape beginners, being compatible with e-liquids at high nicotine rates, with a nicotine salt, or with CBD.

This vape type favors optimal flavor rendering, here heightened thanks to B Series MTL coils from the manufacturer.

By choosing the Z Nano MTL, you'll get a 4ml tank fillable by the top and an efficient and leakproof top airflow.

Its standard 510 pin enables you to connect the clearomizer to all your mods with a minimal diameter of 24mm.

The Z Nano MTL clearomizer with Lost Vape's Thelema Quest Solo 100W mod

A look made for the MTK version of the Z Nano

Unlike other versions of the Nano series, the Z Nano MTL features a straight Pyrex glass tube covered with stainless steel bands.

This detail not only protects it from scratches and impacts, but also gives it a more modern and high-quality look.

Its 24mm diameter base widens quickly to 26.5mm, allowing you to connect your clearomizer to most mods on the market.

The two included drip tips are designed for a tight draw with indirect inhaling; you can choose the format that suits you best according to your needs.

Geekvape's Z Nano MTL clearomizer

Tailor-made coils

Geekvape specially added two coils to its B Series collection, made for the Z Nano MTL.

With its two MTL versions (indirect inhaling), the manufacturer guarantees a better flavor rendering while procuring a good vapor volume.

Discover it in the Z Nano MTL box:

• 1 1.2ohm B Series MTL coil: for a tight vape, to use between 8 and 12 watts
• 1 0.8ohm B Series MTL coil (pre-installed): for a slightly more airy draw, to use between 12 and 16 watts

After two to three weeks of use, your coil starts to show some signs of wear (loss of flavors, light burnt taste).

It will be time to replace it with a new one.

For this:

1. Unscrew the bottom part of Z Nano MTL
2. Take the coil out with the small key included
3. Soak a new coil with some e-liquid drops
4. Insert the latter in the compartment in place of the old one
5. Screw back the bottom part of the clearomizer
6. Wait for some minutes before vaping so the coil is correctly primed

An efficient and precise top airflow

Although the Z Nano MTL is designed for a tight draw with indirect inhaling, you can still vary your vaping experience.

This is thanks to the air intake adjustment via the rotating ring located on the top of the clearomizer. Geekvape focuses on precision with a system of small notches, allowing you to adjust the airflow to suit your needs.

Also, by opening or closing the micro-perforations in the top airflow, you can quickly and easily switch from a very tight draw to a slightly less restrictive vape.

The airflow of Geekvape's Z Nano MTL clearomizer

How to fill your tank?

Here too, Geekvape focuses on precision and efficiency!

With a capacity of 4ml, the Z Nano MTL tank offers good vaping capacity, with the indirect inhaling draw consuming little e-liquid.

In addition, the manufacturer has equipped the clearomizer with a handy top-fill system.

When it's time to fill your tank, take your dropper bottle and:

1. Push the top cap to the red mark
2. Insert the tip of the bottle into the filling hole
3. Gently pour your e-liquid into the tank until it is three-quarters full
4. Push the top cap in the opposite direction to close it

Remember to wait 5 to 10 minutes before vaping if you are using a new coil.

The filling of Geekvape's Z Nano MTL clearomizer

Box contents

• 1 4ml Z Nano MTL clearomizer
• 1 0.8ohm B Series MTL coil (pre-installed)
• 1 1.2ohm B Series MTL coil
• 1 spare Pyrex
• 1 spare 510 drip tip
• 1 set of spare pieces
• 1 user guide

The Z Nano MTL clearomizer is made by Geekvape.

Box contents of Geekvape's Z Nano MTL clearomizer