Geekvape Zeus Fli Clearomizer

A clamshell top cap and a 5.5ml tank: the god of clouds strikes again! Discover Geekvape's Z Fli clearomizer in a video!

The power of Zeus takes over the vape world once again, but this time, with a more accomplished version of its sub-ohm clearomizer. Discover below the clever improvements of Geekvape, for its Zeus (Z) Fli (Flip)!

With a tank of 5.5ml and a handy top cap opening, this clearomizer is particularly meant for enthusiasts of big clouds, in direct inhaling (DL).

Geekvape's Zeus Fli clearomizer on Vaporesso's Armour Max mod

To enhance all your mods

After the international success of the Zeus Sub Ohm clearomizer, Geekvape offers a new version with better performances, especially with a flip top-cap system and optimized airflow settings.

Its height of 51.5mm and its width of 29mm perfectly go with all mods of a 26mm diameter at least. In comparison to its predecessor, the bulb tank was slightly widened, to reach a 5.5ml e-liquid capacity.

At the top of the Zeus Fli clearomizer, you'll find a beautiful 810 drip-tip, dedicated to big clouds production, in direct inhaling (DL).

The Zeus Fli clearomizer by Geekvape

Improved Z Series coils: Z XM

Geekvape gives its Zeus Fli mystical Z Series coils and completes it with two versions made for this nice clearomizer:

• 1 Z XM coil of 0.15ohm (already installed): to use between 70 and 85W
• 1 Z XM coil of 0.4ohm: to use between 50 and 60W

Remember to use these two coils are meant for intense vapor production, for a very airy draw in direct inhaling (DL).

How to replace your coil

After two to three weeks of use, your coil will probably show some wearing signs (loss of flavors, light burn taste...); then it is time to replace it with a new one.

For this:

1. Unscrew the lower part of the Zeus Fli clearomizer
2. Pull the used coil to take it off
3. Soak a new Z Series coil with some drops of e-liquid
4. Put it in the same place as the old one
5. Screw the low part back
6. Fill it with e-liquid
7. Wait for 5 to 10 minutes so that the new coil is correctly soaked in e-liquid

An even more precise airflow system

With its Zeus Fli, Geekvape keeps the same top airflow system as its predecessor, but with an airflow ring with clever craved grooves for meticulous airflow settings.

You can switch from an airy draw to a more restrictive inhaling by simply spinning it.

This top airflow system is also a good leakproof advantage for a clean and dry clearomizer at all times!

The airflow ring of the Zeus Fli clearomizer by Geekvape

Fli for flip!

The ingenious top cap opening system of the Zeus clearomizer is the main innovation but it also gives its name to the clearomizer.

Still a top filling tank, you can access it by unclipping the cap of the high part of the clearomizer, where is the 810 drip-tip. The flip system allows you to keep the cap attached for an easy and quick filling.

When you need to fill the bubble tank of 5.5ml, you just have to:

1. Open the flip top cap
2. Insert the bottle tip in the filling hole
3. Pour your e-liquid to three-quarters
4. Clip the top cap back on the Zeus Fli clearomizer
5. Wait for 5 to 10 minutes before vaping it if you're using a new coil

Note that for this kind of clearomizer, it is recommended to use high-rate vegetable glycerin (70%) e-liquids.

The top-fill system of the Zeus Fli clearomizer by Geekvape

Contents of the box

• 1 Zeus Fli clearomizer
• 1 0.15ohm Z Series XM coil (already installed)
• 1 0.4ohm Z Series XM coil
• 1 spare bulb Pyrex
• 1 set of spare parts
• 1 user guide

The contents of the Zeus Fli clearomizer box by Geekvape

The Zeus Fli clearomizer is made by Geekvape.