Geek Vape P Subohm Clearomizer

Discover the P Subohm, a clearomizer with advanced looks and performance!

With a diameter of 24 mm at the base (26 mm in total) and a 5 ml top-fill tank, nothing will spoil your power vaping sessions.

But above all, you will discover a whole new way of vaping, thanks to its triple-opening middle airflow and two reinforced Pyrex tanks.

The P Subhom clearomizer with Smok's Arcfox mod

A design with two levels

This clearomizer is 59.35mm high and 24mm in diameter at the base, with a total diameter of 26mm. It has been designed with a two-stage model.

Unlike traditional clearomizers, it is made from two Pyrex tanks separated by an airflow ring. Finally, you will find the traditional top cap with a top-filling system and an 810 drip tip!

And, of course, a 510 connector so you can attach your 26mm diameter clearomizer to any type of mod!

The P Subohm clearomizer by Geek Vape

The Z Series coils

To ensure a dense and cloudy rendering, Geekvape has chosen the Z Series coils as companions for its P Subohm Tank! Already included with your clearomizer, you will find:

• A Z Series Z0.2 Dual Mesh coil, with a value of 0.2ohm, already pre-installed in your clearo. It will be used between 70 and 80 watts for a dose of vapor, without loss of flavor!

• A Z Series Z0.4 Mesh coil, with a value of 0.4ohm, for use between 50 and 60W, still in air vape, but a little more restrictive.

To set up your Z Series Coil, you will proceed as follows:

1. Unscrew the 510 base of your clearomizer (bottom part, below the tank)
2. Remove the used coil
3. Take a new coil and soak its cotton parts with a few drops of e-liquid to prime it
4. Place it in the centre of the tank, using the detour pins
5. Screw the bottom of the clearomizer P Subohm

The middle airflow of P Subohm

After the inevitable top-airflow of Geek Vape clearomizers and atomizers, say hello to the new system of the manufacturer, the middle airflow! Housed between the two Pyrex tanks of your P Subohm, a sublime airflow knob will allow you to precisely adjust your draw.

Slightly offset from the other components of the P Subohm, this small rotating part will be very easy to handle, ensuring you an easy and thorough adjustment of your airflow. The P Subohm clearomizer has three large airflow windows, for a very cloudy (DTL) or more restrictive (RDL) draw.

The middle airflow of the P Subhom clearomizer by Geek Vape

How to fill the P Subohm?

With its two-stage structure, the P Subohm clearomizer not only offers a capacity of 5ml, but also boasts a unique design. What's more, it is certified easy to dismantle, making cleaning and replacing parts a breeze!

As you know, with Geekvape, filling is always simple and clean! What's more, refilling is done from the top (top-fill system) by simply unscrewing the top cap (upper part with drip tip) of your clearomizer. Insert the tip of your bottle, avoiding the central hole. Then close the top cap and wait several minutes (at least 15) for the coil to prime completely.

The top-fill system of the P Subohm clearomizer by Geek Vape

Box contents of the P Subohm clearomizer

• A P Subohm clearomizer
• Two spare Pyrex - 5ml total capacity
• A spare 810 drip-tip
• A 0.2Ω Z Series coil (pre-installed)
• A 0.4Ω Z Series coil
• A set of spare O-rings
• A user guide

The P Subohm clearomizer is made by Geek Vape.

Contents of the box of the P Subohm clearomizer by Geek Vape