BP Mods Labs MTL RTA Atomizer

Discover BP Mods' Labs MTL RTA atomizer in this video from our panda expert!

If you are a fan of quality MTL vapes, BP Mods’ atomizer is made for you. Measuring 22mm wide and equipped with a 2.7ml tank, the Labs MTL RTA is an effective and discreet atomizer.

Discover a complete kit that allows for much customization and uses single-coil builds. Indeed, there are 4 different bells for you to choose from, which can be swapped depending on the type of e-liquid you’re vaping.

BP Mods’ Labs MTL RTA atomizer on Geek Vape’s Aegis Solo 2 S100 mod

An elegant and slender shape

BP Mods has opted for a sleek and modern design for its Labs MTL RTA, making it compatible with any mods that can accommodate a diameter of 22mm.

It’s 38.6mm high (without the drip tip), so it’s quite long and slim for an atomizer.

Its stainless steel body has fine grooves and holds a very narrow tank at the top of the device.

BP Mods’ Labs MTL RTA atomiser

A single-coil deck with airflow inserts

The Labs MTL RTA comes with all the accessories needed for single-coil builds and promises long hours of tasty indirect inhale (MTL) vaping.

Inside the kit are 3 coils of different resistive values:

• One 0.7ohm Ni70 single coil (26Ga)
• One 0.85ohm A1 Clapton coil (30Ga*2 + Ni 40Ga)
• One 0.55ohm A1 Clapton coil (28Ga-2 +Ni80 70Ga)

You can easily set up the coil of your choice on the Labs MTL RTA’s deck, which is located on the lower part of the atomizer. To do so, screw the coil using the two flathead screws on either side of the deck. Once the coil is in place, simply thread a wick of cotton through it and trim it to size, following the edge of the deck. Finally, soak the cotton with a few drops of e-liquid before vaping.

The Labs MTL RTA kit also contains 6 airflow inserts that allow you to adjust your vaping style. They measure 0.8mmx2, 0.8mm, 1.0mm,1.1mm,1.2mm and 1.5mm, respectively. To change the insert, located in the middle of the deck, unscrew it using the tool included in the kit.

The airflow inserts of BP Mods’ Labs MTL RTA atomizer

Different bells for different flavors

The Labs MTL RTA also features a system of interchangeable bells, which can be swapped according to the e-liquid flavor you’re vaping:

• A bell for dry flavors, such as tobacco
• A bell for rich and mellow flavors, like sweets
• A bell for smooth, fruity, and creamy liquids
• A bell for complex flavors, such as tobacco blends and spicy e-liquids

Feel free to test them out to find the one that suits your vaping preferences!

This bell sits right on top of the deck. If you want to change it, use the tool included in the kit (the same one that’s used for the inserts). Simply insert the tip of the tool into the drip tip’s hole and push the top-notch downwards.

The bells of BP Mods’ Labs MTL RTA atomizer

A 2.7ml tank

The Labs MTL RTA is dedicated to tight indirect inhale vaping, so the tank’s 2.7ml capacity will be more than enough for that kind of use.

BP Mods has made filling the tank easy for you. Simply unscrew the top cap by a quarter turn to remove it. Then, you can access the 2.7ml tank. All you have to do is pour your e-liquid into the said tank and place the top cap back on the atomizer!

We recommend not filling the tank to the brim.

Filling BP Mods’ Labs MTL RTA atomizer

Contents

• The Labs MTL RTA atomizer
• 6 Airflow inserts
• 4 bells
• 3 ready-made coils
• A special screwdriver for the inserts and bells
• A set of spare parts

The Labs MTL RTA atomizer is manufactured by BP Mods.

The contents of BP Mods’ Labs MTL RTA atomizer kit