BD Vape Rayden 100 V3 Limited Edition Kit

BD Vape is introducing the third version of its Rayden 100 mod with the Rayden 100 V3 IM Limited Edition kit, produced in a limited run of just 3,000 copies. This series draws inspiration from the visual design of IM's armor and pairs the mod with its Blaster 2 Sub-Ohm clearomizer.

The result? A kit designed for fans of airy direct (DL) vaping, powered by the XT Ultra GT 100 V1.1 chipset.

The Rayden 100 V3 IM mod is powered by a 21700 or 18650 battery (not included), with the 18650 battery adapter included in the box.

BD Vape pairs this electronic mod with the Blaster 2 Sub-Ohm clearomizer, which is compatible with the manufacturer’s BDC coils. Its tank has a 5ml capacity, expandable to 7ml using the included replacement Pyrex tube.

The Blaster 2 Sub-Ohm features a top-fill system, as well as a precisely adjustable top airflow.

BD Vape's Rayden 100 V3 Limited Edition kit

A design with refined finishes

The kit measures 157 x 34 x 30.5 mm and weighs 213 grams.

Its case, which features the same design elements as the IM armor, is made of stainless steel and aluminum alloy, making it both sturdy and lightweight.

On the front panel, you'll find:

• 1 Fire button
• 1 1.05" HD TFT screen
• Adjustment buttons below the screen

As for the USB-C port, it's located on the bottom of the mod, allowing for both charging and chipset updates.

The Blaster 2 Sub-Ohm clearomizer also features a gold finish that matches the box's color scheme.

It retains the distinctive silhouette of the original Blaster with its 810 drip tip, while offering even more refined finishes for this limited edition.

Handling of BD Vape's Rayden 100 V3 Limited Edition kit

How does the Rayden 100 V3 Limited Edition kit work?

The XT Ultra GT 100 V1.1 chipset controls the device's operation, delivering up to 100W of power.

The display and control buttons give you access to 7 operating modes:

• Voltage Mode: manual adjustment of the output voltage between 1V and 8V
• Bypass Mode: the battery voltage is delivered directly based on its charge level and the installed coil
• MTL (Power): smooth power curve for a consistent MTL vape
• Soft (Power): starts at a power level lower than the set value, then gradually increases it
• Norm (Power): stable and constant power
• Hard (Power): delivers a higher power output upon activation before returning to the set value
• Pro: allows you to create a custom power profile, ranging from 5 to 100W over a duration of 0 to 8 seconds

Want to customize the information on your screen? You can! The interface also offers several display themes (Classic 1, Classic 2, I MAN, or a custom theme using your own images).

The screen of BD Vape's Rayden 100 V3 Limited Edition kit

Power your kit with a 21700 or 18650 battery

To power your kit, you'll need to insert a 21700 battery or an 18650 battery using the included adapter.

Unscrew the cap located under the mod and slide your battery into the compartment, making sure to follow the indicated polarity directions.

The battery compartment of BD Vape's Rayden 100 V3 Limited Edition kit

Once the battery is inserted, you can also charge it directly from the mod using the included USB-C cable.

The USB-C port of BD Vape's Rayden 100 V3 Limited Edition kit

The Blaster 2 Sub-Ohm clearomizer

BD Vape equips its Rayden 100 V3 IM Limited Edition mod with a Blaster 2 Sub-Ohm, a clearomizer focused on an airy vape in direct inhaling.

With a 5ml tank, you'll change it with a 7ml Pyrex included in the box to increase its e-liquid capacity.

The Blaster 2 Sub-Ohm clearomizer of BD Vape's Rayden 100 V3 Limited Edition kit

The BDC coils

BD Vape delivers your kit with several BDC coils, to select according to your draw preferences:

• 0.15ohm BDC coil: for use between 60 and 75W
• 0.3ohm BDC coil: for use between 45 and 60W
• 0.4ohm BDC coil: for use between 40 and 50W

After several weeks of use, your coil will begin to show signs of wear, such as a loss of flavor.

To replace it:

1. Unscrew the bottom section of the Blaster 2 Sub-Ohm clearomizer
2. Carefully remove the worn-out coil
3. Soak the new coil with a few drops of e-liquid
4. Insert the new coil into the designated compartment
5. Screw the bottom section of the clearomizer back on

Wait a few minutes before vaping to allow the coil to properly soak up the e-liquid.

The Blaster 2 Sub-Ohm's top airflow

The Blaster 2 Sub-Ohm features an adjustable airflow located on the top, thereby minimizing the risk of leaks.

To adjust your draw, simply rotate the dedicated ring, alternating between an open draw and a tighter vape.

The top airflow of BD Vape's Rayden 100 V3 Limited Edition kit

How to fill the tank?

Whether you use the original 5ml Pyrex tank or the included 7ml one, the Blaster 2 Sub-Ohm features a top-fill system.

To refill with e-liquid:

1. Twist the top cap to remove it
2. Insert the narrow tip of your bottle into the fill port
3. Pour e-liquid until the tank is three-quarters full
4. Carefully replace the top cap

Caution: Wait at least 5 to 10 minutes before vaping if you are using a new coil.

The filling system of BD Vape's Rayden 100 V3 Limited Edition kit

Box contents

• 1 BD Vape Rayden 100 V3 IM Limited Edition mod
• 1 5ml Blaster 2 Sub-Ohm clearomizer
• 1 7ml spare Pyrex
• 1 0.15ohm BDC coil
• 1 0.3ohm BDC coil
• 1 0.4ohm BDC coil
• 1 adaptor for 18650 battery
• 1 bag of accessories
• 1 USB-C cable
• 1 user guide

The Rayden 100 V3 IM Limited Edition kit is made by BD Vape and sold without batteries.

Box contents of BD Vape's Rayden 100 V3 Limited Edition kit