Mission XV X Dotmod DotApollo Kit

DotApollo: the high-end AIO kit by Dotmod and Mission XV

The DotApollo joins the world of high-quality All-In-One kits, with a design that is as stylish as it is effective.

Designed for a single 18650 battery (not included), it delivers a maximum power of 80 watts.

Its DotAIO V4 tank has a 4 ml e-liquid capacity and is specially designed to accommodate the manufacturer's DotCoil coils.

Created by Dotmod in collaboration with Canadian modders Mission XV, the DotApollo has a 0.96'' screen, giving you access to a wide range of settings.

Dotmod and Mission XV's DotApollo kit

A compact AIO format

Dotmod and Mission XV have joined forces to bring you a kit made from a single piece, with a meticulously designed finish.

Measuring 92.5x40mm, the DotApollo has a handy, ergonomic pocket size.

Its aluminum alloy construction makes it very lightweight, weighing only 88g (without battery).

The screen, cartridge, and power switch are visible, while the USB port and adjustment buttons are hidden under two magnetic panels.

The 18650 battery (sold separately) is partially covered by a magnetic cover, protecting it from shocks and scratches.

Handling of Dotmod and Mission XV's DotApollo kit

Several setting modes

According to the vape experience desires, Dotmod and Mission XV offer different functioning modes.

Use the screen and the setting buttons to select the one that suits you among:

• PM (power) mode: manual power adjustment, from 5 to 80W
• BP (Bypass) mode: simulates the experience of a mechanical mod, while retaining the electronic safety features of the chipset
• Auto mode: automatic adjustment of the power according to the value of the DotCoil used
• Curve mode: modulation of the power with each puff
• Boost mode: different power settings at the start and end of a puff

The screen of Dotmod and Mission XV's DotApollo kit

A capacity in dual batteries

One of the many advantages of the DotApollo is its power supply system.

Dotmod and Mission XV give you control over your kit's capacity by providing a slot for an 18650 battery (sold separately).

Remember to bring a spare charged battery so you never run out of power for your e-cigarette!

The 18650 single battery compartment of Dotmod and Mission XV's DotApollo kit

Is your battery out?

Use the USB-C cable included in the kit box and connect it to the port covered by a magnetic panel.

However, we recommend using an external charger for your battery whenever possible, particularly to preserve its service life.

The USB-C port of Dotmod and Mission XV's DotApollo kit

The DotAIO V4 tank

For their DotApollo, Dotmod and Mission XV bet on their DotAIO V4, a 4ml tank compatible with the DotCoils.

This cartridge is topped with a Vortex drip tip with a spiral chimney, specially designed for your AIO kit.

The DotApollo kit is also compatible with older generations of DotAIO tanks.

The DotAIO V4 tank of Dotmod and Mission XV's DotApollo kit

The DotCoil

The DotApollo kit can be used upon its receipt thanks to the two DotCoils included in the box.

Simply select the one that suits you among the two offered:

• 0.7ohm DotCoil coil: to use between 14 and 20W, for a tight vape in indirect inhaling (MTL)
• 0.3ohm DotCoil coil (pre-installed): to use between 25 and 40W, for an airier draw in restrictive direct inhaling (RDL), or direct inhaling (DL)

After two to three weeks of use, your coil will start to show some signs of wear (loss of flavors, light burnt taste).

It will be time to replace it with a new one.

For this:

1. Unscrew the drip tip
2. Take out the cartridge
3. Slightly pull on the bottom part to take it off
4. Take the used coil
5. Soak a new coil with some drops of e-liquid
6. Insert it in its compartment in place of the old one
7. Replace the bottom part of the cartridge
8. Fill the e-liquid tank
9. Reconnect the tank on the kit
10. Screw the drip tip to keep the cartridge in the kit
11. Wait for some minutes so the coil is correctly primed

An adjustable airflow

According to the type of draw desired, easily set the airflow by using the airflow wheel located under the DotAIO V4 tank.

The more the airflow is open, the more airy the vape!

The airflow of DotAIO V4 tank of Dotmod and Mission XV's DotApollo kit

How to fill your tank?

When it's time to refill the 4 ml DotAIO V4 tank with e-liquid, there's no need to remove it from the kit.

Simply take your dropper bottle and:

1. Lift the silicone strip on the front of the cartridge
2. Insert the tip of your bottle into the filling hole
3. Gently pour in your e-liquid
4. Carefully close the strip

Reminder: wait a few minutes before vaping if you are using a new coil.

The filling of Dotmod and Mission XV's DotApollo kit

Box contents

• 1 80W DotApollo
• 1 4ml DotAIO V4 tank
• 1 0.3ohm DotCoil (pre-installed)
• 1 0.7ohm DotCoil
• 1 USB-C cable
• 1 user guide

The DotApollo kit is made by Dotmod in collaboration with Mission XV.

Box contents of Dotmod and Mission XV's DotApollo kit